Manual Yamaha XV920 Virago (page 307 of 363) (English)

689861

307

Zoom out

Zoom in

1/363

8A-4

Chapter 8 Part A Electrical system (XV535 models)

5.1a The main and accessory fuses are

located in a fuse block under the seat

(this is an early model)...

5.1b ... and this is a later model 5.1c Lift the cover for access to the fuse

(early model shown)

brush or knife and emery paper. Reconnect the cables and apply a thin

coat of petroleum jelly to the connections to slow further corrosion.

5 The battery case should be kept clean to prevent current leakage,

which can discharge the battery over a period of time (especially when

it sits unused). Wash the outside of the case with a solution of baking

soda and water. Do not get any baking soda solution in the battery

cells. Rinse the battery thoroughly, then dry it.

6 If acid has been spilled on the frame or battery box, neutralize it

with the baking soda and water solution, dry it thoroughly, then touch

up any damaged paint. Make sure the battery vent tube is directed

away from the frame and is not kinked or pinched.

7 If the motorcycle sits unused for long periods of time, disconnect

the cables from the battery terminals. Refer to Section 4 and charge

the battery approximately once every month.

4 Battery - charging

1 If the machine sits idle for extended periods or if the charging

system malfunctions, the battery can be charged from an external

source.

2 To properly charge the battery, you will need a charger of the

correct rating, a hydrometer, a clean rag and a syringe for adding

distilled water to the battery cells.

3 The maximum charging rate for any battery is 1/10 of the rated

amp/hour capacity. As an example, the maximum charging rate for a

12 amp/hour battery would be 1.2 amps and the maximum charging

rate for a 14 amp/hour battery would be 1.4 amps. If the battery is

charged at a higher rate, it could be damaged.

4 Do not allow the battery to be subjected to a so-called quick

charge (high rate of charge over a short period of time) unless you are

prepared to buy a new battery.

5 When charging the battery, always remove it from the machine

and be sure to check the electrolyte level before hooking up the

charger. Add distilled water to any cells that are low.

6 Loosen the cell caps, hook-up the battery charger leads (red to

positive, black to negative), cover the top of the battery with a clean

rag, then, and only then, plug in the battery charger. Warning:

Remember, the gas escaping from a charging battery is explosive, so

keep open flames and sparks well away from the area. Also, the

electrolyte is extremely corrosive and will damage anything it comes in

contact with.

7 Allow the battery to charge until the specific gravity is as specified

(refer to Chapter 1 for specific gravity checking procedures). The

charger must be unplugged and disconnected from the battery when

making specific gravity checks, if the battery overheats or gases

excessively, the charging rate is too high. Either disconnect the

charger or lower the charging rate to prevent damage to the battery.

8 It's time for a new battery if:

a) One or more of the cells is significantly lower in specific gravity

than the others after a long slow charge.

b) The battery as a whole doesn't seem to want to take a charge.

c) Battery voltage won't increase.

d) The electrolyte doesn't bubble.

e) The plates are white (indicating sulfation) or debris has

accumulated in the bottom of a cell.

f) The plates or insulators are warped or buckled.

9 When the battery is fully charged, unplug the charger first, then

disconnect the leads ffom the battery. Install the cell caps and wipe

any electrolyte off the outside of the battery case.

5 Fuses - check and replacement

Refer to illustrations 5.1a, 5.1b and 5.1c

1 The fuse block is located beneath the top cover (early models) or

the seat (later models) (see illustrations). It contains a 20-amp or 30-

amp main fuse, spare fuses and accessory fuses (see illustration)

Fuse functions and ratings are listed in this Chapter's Specifications.

Fuse ratings are marked on the fuses.

2 If you have a test light, all of the fuses can be checked without

removing them. Turn the ignition key to the On position, connect one

end of the test light to a good ground, then probe each terminal on top

of the fuse. If the fuse is good, there will be voltage available at both

terminals. If the fuse is blown, there will only be voltage present at one

of the terminals.

3 The fuses can also be tested with an ohmmeter or self-powered

test light. Remove the fuse and connect the tester to the ends of the

fuse. If the ohmmeter shows continuity or the test lamp lights, the fuse

is good. If the ohmmeter shows infinite resistance or the test lamp

stays out, the fuse is blown.

4 The fuses can be removed and checked visually. If you can't pull

the fuse out with your fingertips, use a pair of needle-nose pliers. A

blown fuse is easily identified by a break in the element.

5 If a fuse blows, be sure to check the wiring harnesses very

carefully for evidence of a short circuit. Look for bare wires and

chafed, melted or burned insulation. If a fuse is replaced before the

cause is located, the new fuse will blow immediately.

6 Never, under any circumstances, use a higher rated fuse or bridge

the fuse block terminals, as damage to the electrical system could

result.

7 Occasionally a fuse will blow or cause an open circuit for no

obvious reason. Corrosion of the fuse ends and fuse block terminals

may occur and cause poor fuse contact. If this happens, remove the

corrosion with a wire brush or emery paper, then spray the fuse end

and terminals with electrical contact cleaner.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha XV920 Virago in the language / languages: English as an attachment in your email.

The manual is 52,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yamaha XV920 Virago Manual

Product: