689861

Yamaha XV920 Virago Manual

309
Zoom out
Zoom in
Previous page
1/363
Next page
8A-6 Chapter 8 Part A Electrical system (XV535 models)
8.3 The headlight adjusting screws are
located on either side of the headlight
assembly; the vertical adjusting screw is
at the lower right (arrow); the horizontal
adjusting screw is at the upper left
9.2 Remove the pivot bolt and nut at the
bottom (arrows) and the mounting bolt
inside the headlight assembly
10.2 Press the bulb into the socket and
turn it counterclockwise (anti-clockwise
to remove
10.5 Remove the lens screws (arrows) and take off the lens
10.6 Press the bulbs into their sockets and turn counterclockwise
(anti-clockwise) to remove
2 The headlight beam can be adjusted both vertically and
horizontally. Before performing the adjustment, make sure the fuel tank
is at leasi half full and have an assistant sit on the seat.
3 The horizontal adjusting screw is at the upper left of the headlight
cover (see illustration). The vertical adjusting screw is located at the
lower right.
9 Headlight assembly - removal and installation
Refer to illustration 9.2
1 Remove the headlight cover (see Section 7). If you're planning to
take the headlight assembly completely off the motorcycle, disconnect
the electrical connectors inside the headlight assembly. If you're just
removing the assembly for access to the speedometer, the connectors
can be left attached.
2 Remove the mounting bolt inside the headlight cover and the
pivot bolt at the bottom (see illustration). Slide the assembly down
and forward so the mounting grommet can clear the post, then take
the assembly off the motorcycle.
3 Installation is the reverse of the removal steps.
10 Turn signals and tail/brake light bulbs - replacement
Turn signal bulbs
Refer to illustration 10.2
1 To replace a turn signal bulb, remove the screws that hold the
lens to the turn signal housing and take off the lens.
2 Push the bulb in and turn it counterclockwise (anti-clockwise) to
remove it (see illustration).
3 Check the socket terminals for corrosion and clean them if
necessary. Line up the pins on the new bulb with the slots in the
socket, push in and turn the bulb clockwise until it locks in place.
Note: The pins on US model front turn signal bulbs are offset so they
can only be installed one way. It is a good idea to use a paper towel or
dry cloth when handling the new bulb to prevent injury if the bulb
should break and to increase bulb life.
4 Position the lens on the housing and install the screws. Be careful
not to overtighten them or the lens will crack.
Tail/brake light bulbs
Refer to illustrations 10.5 and 10.6
5 Remove the lens screws and take the lens off (see illustration).
6 . Push the bulb in and turn it counterclockwise (anti-clockwise) to
remove it (see illustration).
7 Perform Steps 3 and 4 above to install the bulb, noting that the
pins are offset.
… 309 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha XV920 Virago at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha XV920 Virago in the language / languages: English as an attachment in your email.

The manual is 52,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info