571272
217
Zoom out
Zoom in
Previous page
1/300
Next page
Reference Performance Mode
Performance Edit mode Part Edit
217
Owner’s Manual
[SF5] OTHER
PB (Pitch Bend) Upper,
PB (Pitch Bend) Lower These two parameters are available for Parts 1 - 4 to which the internal Normal Voices are assigned. These
determine the pitch change range (in semitones) of the Pitch Bend wheel for the Part’s Voice. For example, a Lower
setting of -12 would result in the pitch being lowered up to a maximum of one octave (12 semitones) when the Pitch
Bend wheel is moved downwards. Similarly, setting the Upper parameter to +12 would result in a maximum pitch
rise of one octave when the wheel is moved upwards.
Settings: -48 ~0 ~+24
PB (Pitch Bend) Range This parameter is available for Parts 1 - 4 to which the internal Drum Voices are assigned and Plug-in Parts 1 - 3. This
determines the pitch change range (in semitones) of the Pitch Bend wheel. Unlike the Pitch Bend setting for Parts 1
- 4 to which the internal Normal Voices are assigned described above, the Upper and Lower ranges of the Drum
Voice Parts and Plug-in Parts cannot be set independently.
Settings: -24 ~ 0 ~ +24
VelSensDpt
(Velocity Sensitivity Depth) Determines the degree to which the resulting volume of
the tone generator responds to your playing strength.
The higher the value, the more the volume changes in
response to your playing strength (as shown at right).
Settings: 0 ~ 127
VelSensOfst
(Velocity Sensitivity Offset) Determines the amount by which played velocities are adjusted for the actual resulting velocity effect. This lets you
raise or lower all velocities by the same amount — allowing you to automatically compensate for playing too strongly
or too softly.
Settings: 0 ~ 127
[F2] OUTPUT
[SF1] VOL/PAN (Volume/Pan)
Volume Determines the volume for each Part, giving you detailed control over the level balance among the Parts.
Settings: 0~127
Pan Determines the stereo pan position for each Part.
Settings: L63 (far left) ~ C (center) ~ R63 (far right)
VoiceELPan (Voice Element Pan) Determines whether the individual pan settings for each Voice (made via [VOICE] [EDIT] Element selection
[F4] AMP [SF1] LVL/PAN Pan) are applied or not. When this is set to “off,” the basic pan position for the
selected Part is set to center.
Settings: on, off
nThis parameter is not available for the Plug-in Parts.
[SF2] EF SEND (Effect Send) From this display you can set the Send Level and Dry Level sent to the System Effects for each Part. For details
about the Effect connection in the Performance mode, see page 179.
RevSend (Reverb Send) Determines the send level for the Reverb effect of the selected Part, giving you detailed control over the Reverb
balance among the Parts.
Settings: 0~127
ChoSend (Chorus Send) Determines the send level for the Chorus effect of the selected Part, giving you detailed control over the Chorus
balance among the Parts.
Settings: 0~127
Dry Level Determines the level of the unprocessed (dry) sound of the selected Part, letting you control the overall effect
balance among the Parts.
Settings: 0~127
127
0 127
Depth = 127
Depth = 32
Depth = 64
Depth = 0
When Offset (below) is set to 64:
Actual resulting
velocity (affecting the
tone generator)
Velocity with which you play a note
127
0 12764 12764 127
64
127
0
127
0
When Depth (above) = 64 and Offset = 32 When Depth (above) = 64 and Offset = 64 When Depth (above) = 64 and Offset = 96
Actual resulting
velocity (affecting
the tone generator)
Velocity with which you play a note
217


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MOTIF ES7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MOTIF ES7 in the language / languages: English as an attachment in your email.

The manual is 8,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha MOTIF ES7

Yamaha MOTIF ES7 Installation Guide - English - 35 pages

Yamaha MOTIF ES7 Installation Guide - German - 35 pages

Yamaha MOTIF ES7 User Manual - German - 300 pages

Yamaha MOTIF ES7 User Manual - Dutch - 300 pages

Yamaha MOTIF ES7 User Manual - French - 300 pages

Yamaha MOTIF ES7 Installation Guide - French - 35 pages

Yamaha MOTIF ES7 User Manual - Italian - 308 pages

Yamaha MOTIF ES7 Installation Guide - Italian - 12 pages

Yamaha MOTIF ES7 User Manual - Portuguese - 300 pages

Yamaha MOTIF ES7 User Manual - Spanish - 297 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info