29781
9
Zoom out
Zoom in
Previous page
1/16
Next page
9
ENGLISH
B/ C/MPX FILTER indicators
Display during recording
L
R
dB
–30 20 15 10 8 6 4 0 2
Ÿ
46
+
SOURCE
REC
TAPE
TAPE TUNING
I/NORM II/HIGH IV/METAL
MPX FILTER
Ÿ
B C
Peak level meters
TAPE TUNING indicator
SOURCE/TAPE indicators
Note:
The tape remain indicator may differ depending on the tape
length, tape type or the size of hub. So, use this indicator as
an aid to recognize the remaining length of the tape to be
played back.
To stop recording temporarily
Press the REC/PAUSE button. To resume recording,
press the 3 PLAY button.
To stop recording and remove the cassette
tape
Press the 7 STOP button and then the ) button. The
cassette tray comes out and you can remove the cassette
tape.
To enter the standby mode
Press the STANDBY/ON switch again.
Three head system
The three-head system allows the just-recorded sound to be
monitored while recording. You can compare the difference
between the recorded sound and the source sound by
switching the monitor mode (SOURCE or TAPE) with the
MONITOR button, so you can try to obtain a recording
sound identical to the source sound.
To monitor the just recorded sound
Setting the recording level (in step 3)
Play the loudest passage of the source to be recorded and
watch the meter readings. When using Normal position
tapes (type I/NORM) or High position tapes (type II/HIGH
(CrO2)), adjust the REC LEVEL control so that the highest
peak is +4 dB. When using Metal position tapes (type IV/
METAL), adjust the REC LEVEL control so that the highest
peak is +6 dB. (Refer to the figure below.)
When a tape is loaded,
the corresponding tape
type indicator lights.
Linear time tape counter
Tape remain indicator
Lights during rec pause mode or
recording. Blinks while the sound
muted section is recorded.
To monitor the sound to be recorded
MONITOR
SOURCE
TAPE
MONITOR
SOURCE
TAPE
Highest peak for Normal or High position tapes
L
R
dB
–30 20 15 10 8 6 4 0 2
Ÿ
46
+
Highest peak for Metal position tapes
L
R
dB
–30 20 15 10 8 6 4 0 2
Ÿ
46
+
Linear time tape counter
Use the linear time tape counter as an aid in locating a point
on a tape (–99 min. 59 sec. to 99 min. 59 sec.). To set the
counter reading to “0:00”, press the COUNTER RESET
button.
Note: Precision of counter
The tape counter is not a clock, and so there will be some
errors in the time display compared to the actual recording
time (this cannot be avoided, as a suitable method is
adopted to provide a time display not only during recording
and playback, but also during fast forward and rewind).
The error depends on the type of tape being used.
Tape remain indicator
The tape remain indicator shows the remaining length of the
loaded tape to be recorded.
When the recording reaches the end of the tape, the leftmost
digit of the tape remain indicator blinks.
Lights when a tape is loaded.
Indicates the remaining tape length.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha KX10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha KX10 in the language / languages: English as an attachment in your email.

The manual is 0,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info