655216

Yale SR Series - Smarthome Alarm Manual

15
Zoom out
Zoom in
Previous page
1/20
Next page
15
Low Battery Indication
The App will display the low battery message under the
actual device.
When a device rst shows the low battery signal it has
enough battery capacity to operate for a further month
before complete exhaustion.
Door/Window Contact Battery Change
When the battery is low the LED will light up when the
door/window is opened. The battery is changed as follows:
1. Ensure the system is disarmed.
2. Loosen the case screw and remove the Door/Window
Contact from the base to reveal battery.
3. Using a screwdriver gently lever out the old battery.
4. Insert new CR2032 coin cell battery with the + side
uppermost. See picture on page 16.
5. Press battery into holder rmly with nger and thumb
until a click is heard.
6. Ret sensor on base and tighten bottom case screw.
Switch tamper protection back on.
• Door/Window Contact case tamper conditions are also
indicated by a lit LED, check the tamper before changing
the battery.
PIR Motion Detector & Image / Video Camera
Battery Change
When the battery is low the LED will ash when any motion
is detected. The batteries are changed as follows:
1. Ensure the system is disarmed.
2. Loosen the case screw and remove PIR from base to
reveal the batteries.
3. Insert new batteries observing correct polarity. (Note:
PIR Motion Detector takes 3x AAA alkaline batteries, PIR
Image Camera takes 2x AA alkaline batteries and PIR
Video Camera takes 3 x AA Lithium batteries. The PIR
LED will ash for 30 seconds while initialising.
4. Ret PIR on base and tighten bottom case screw.
• Ensure tamper spring is fully depressed when re-tting
the PIR to the back case. If this has not been done
correctly this will be indicated by a ashing LED on the
PIR.
External Siren Battery Change
When the batteries start getting low the Siren will produce
a series of audible pips and ashes during arming and
disarming.
1. Ensure the system is disarmed. Select “Controller”,
Device List”, click Siren’s Properties (icon on the right)
and set Siren Bypass to the OFF position.
2. Remove the Siren lid and switch the Siren power switch
to OFF.
3. Unscrew the four screws on the battery compartment lid
and remove the cover.
4. Remove the four batteries, wait for 30 seconds, and
replace them with four fresh alkaline “D” batteries.
5. Switch on Siren power and check that the Siren beeps
and ashes.
Warning: After the batteries have been inserted, the
tamper will become active after three hours. Please replace
the cover back onto the Siren quickly.
• Siren case tamper conditions are also signalled by a
series of beeps when the system is armed but not when
the system is disarmed (low battery warning produces a
series of audible pips when armed and disarmed), take
care not to confuse the two dierent conditions.
Changing the Batteries
8
Always use correct type of batteries as replacements because any other battery can
cause problems with the operation of the system. Ensure the correct steps are taken
when changing batteries in tamper protected devices.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yale SR Series - Smarthome Alarm at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yale SR Series - Smarthome Alarm in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info