Manual Yale SR Series - Smarthome Alarm (page 14 of 20) (English)

655216

Zoom out

Zoom in

1/20

Reset Key Pad code

If the Key Pad code is accidentally forgotten, the Key Pad

can be reset to factory default (0000) using the following

steps:

1. Unscrew the two Key Pad case screws and remove Key

Pad back cover (please disable tamper rst).

Locate and remove the battery. See battery change

section (16-17)

2. Press the number ‘4’ key at the same time as reinserting

the battery.

3. Screw the Key Pad case together and re-learn the Key

Pad into the system using the steps described above in

this section.

Using your Key Pad

• The Key Pad can be used to Away Arm and Home Arm

the system using the buttons as shown.

• The system is disarmed by pressing the disarm button

followed by your PIN code.

• An emergency alarm can be activated by pressing the

panic A and B buttons simultaneously. Deactivate panic

event by pressing the disarm button followed by your PIN

code.

• If there is a system fault, you will need to press the Arm/

Home Arm button for a second time to “force arm” the

system.

Using your Smoke Detector

Smoke Detection

When smoke is detected the device will activate for a

minimum of 10 seconds with a two tone alarm and ashing

LED. The Detector will send a radio signal to the Smart

Hub. You will then be notied via a push notication, SMS

and email .

• Pressing the test button when in an alarm condition will

silence the alarm for 10 minutes. It will automatically

resume smoke detection again after this period.

Testing

• Smoke Detector testing should be done on a regular

monthly basis. Pressing the test button will make the LED

ash, the audible sounder chime and will send a radio

test signal to the Smart Hub when the button is released.

If nothing happens after pressing the test button, it

indicates the batteries will need changing.

Recalibration

• The Smoke Detector might need recalibrating after time

to ensure it is working at its optimum. This is done by

pressing and holding the test button until the LED ashes

and beeps after 10 seconds. The Detector will then start

its self calibration routine.

Using your Panic Button

Activate an Alarm

• Press and hold the red button for at least 3 seconds. The

LED will light momentarily and the alarm will be activated.

Silence an Alarm

1. Press and hold down the red button for 10 seconds.

The LED will light momentarily for a second time and the

alarm will be silenced.

2. Please note that silencing the alarm with the Panic

Button does not reset the system. If the alarm is armed

prior to activation, the system will re-arm after being

silenced with the Panic Button.

3. The system will require a reset at the Smart Hub after

being silenced with the Panic Button.

Using Accessories (cont.)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yale SR Series - Smarthome Alarm in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yale SR Series - Smarthome Alarm Manual

Product: