674754
136
Zoom out
Zoom in
Previous page
1/156
Next page
Page 134 FTDX9000D OPERATION MANUAL
MENU MODE
GENERAL GROUP
028. ANT SELECT
Function: Sets the method of antenna selection.
Available Values: BAND/STACK
Default Setting: BAND
BAND: The antenna is selected in accordance with
the operating band.
STACK: The antenna is selected in accordance with
the band stack (different antennas may be
utilized on the same band, if so selected in
the band stack).
029. BEEP LEVEL
Function: Sets the beep level.
Available Values: 0 ~ 255
Default Setting: 50
030. CAT RATE
Function: Sets the transceiver’s computer-interface
circuitry for the CAT baud rate to be used.
Available Values: 4800/9600/38400 bps
Default Setting: 4800 bps
031. MEM GROUP
Function: Enables/Disables Memory Group Opera-
tion.
Available Values: DISABLE/ENABLE
Default Setting: DISABLE
032. QUICK SPLIT FREQ
Function: Selects the tuning offset for the Quick Split
feature.
Available Values: –20 ~ 0 ~ +20 kHz (1 kHz Step)
Default Setting: +5 kHz
033. TIME OUT TIMER
Function: Sets the Time-Out Timer countdown time.
Available Values: OFF/5/10/15/20/25/30 min
Default Setting: OFF
The Time-Out Timer shuts off the transmitter after
continuous transmission of the programmed time.
034. TRV OFFSET
Function: Set the 10’s and 1’s of the MHz digits dis-
play for operation with a transverter.
Available Values: 30 ~ 49 MHz
Default Setting: 44 MHz
If you connect a 430 MHz transverter to the radio, set
this menu to “30” (the “100 MHz” digits are hidden on
this radio).
035. µTUNE DIAL STEP
Function: Select the µ-TUNE mode.
Available Values: DIAL STEP-1/DIAL STEP-2/OFF
Default Setting: DIAL STEP-1
DIAL STEP-1: Activates the µ-TUNE system in the
Auto mode using “FINE” steps of the
µ-TUNE knob (1 step/click) on the 14
MHz and lower amateur bands on the
main band (VFO-A).
DIAL STEP-2: Activates the µ-TUNE system in the
Auto mode using “COARSE” steps of
the µ-TUNE knob (2 steps/click) on
the 7 MHz and lower amateur bands.
On the 10/14 MHz bands, “FINE” µ-
TUNE knob steps will be used (1 step/
click).
OFF: Disables the µ-TUNE system. Acti-
vates the VRF feature on the 14 MHz
and lower amateur bands on the main
band (VFO-A).
036. MIC SCAN
Function: Enables/disables scanning access via the
microphone’s
[
UP
]
/
[
DWN
]
keys (only available at the
rear panel’s MIC Jack).
Available Values: ENABLE/DISABLE
Default Setting: ENABLE
037. MIC SCAN RESUME
Function: Selects the Scan Resume mode.
Available Values: PAUSE/TIME
Default Setting: TIME
PAUSE: The scanner will hold until the signal disap-
pears, then will resume after one second.
TIME: The scanner will hold for five seconds, then
resume whether or not the other station is
still transmitting.
038. AF/RF DIAL SWAP
Function: Reverses the functions of the AF GAIN
(VFO-B) and RF GAIN (VFO-A) knobs.
Available Values: NORMAL/SWAP
Default Setting: NORMAL
When this menu is set to “SWAP,” you may adjust
the sub (VFO-B) receiver audio using the large RF
GAIN (VFO-A) knob and adjust the main (VFO-A)
receiver RF gain using the small AF GAIN (VFO-B)
knob. This puts both “Volume” controls on the same
shaft.
136


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-DX9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-DX9000 in the language / languages: English as an attachment in your email.

The manual is 25,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info