674732
84
Zoom out
Zoom in
Previous page
1/102
Next page
Page 82 FT-450D OPERATION MANUAL
CWSPEED
Function: Sets the sending speed for the built-in
Electronic keyer.
Available Values: 4 wpm(20cpm)~60wpm(300cpm)
Default: 12wpm (60cpm)
You can set the sending speed in either: wpm (words
per minute), or cpm (characters per minute).
To button between “Wpm” and “cpm”, just press the
[
F
]
button.
Note:
If the CW QSK is set to 25ms, the setting of CW
SPEED must not exceed 50wpm (250cpm); And if
the CW QSK is set to 30ms, the setting of CW SPEED
must not exceed 42wpm (210cpm). The delay will
make it impossible to transmit.
CWSTONE (CW SIDE TONE)
Function: Sets the CW sidetone volume level.
Available Values: FIX0 ~ FIX100 or
LNK-50 ~ LNK 0 ~ LNK+50
Default: FIX10 or LNK-8
CWTRAIN (CW TRAINING)
Function: Setting of CW training function
Available Values: N: / A: / M:
Default: N:
Sends random Morse Code five-character groups via
the sidetone.
N: Numeric characters only
A: Alphabet characters only
M: Numeric and Alphabet characters (Mixed)
CWWEIGT (CW WEIGHT)
Function: Sets the CW weight level.
Available Values: 1/2.5~1/4.5
Default: 1/3.0
Sets the Dot/Dash ratio for the built-in electronic keyer.
D DISP (DATA DISP)
Function: DIG (USER-L or USER-U) mode opera-
tion.
Available Values: -3000Hz ~ 0 ~ +3000Hz
Default: 0
Defines the displayed frequency offset during DATA
(USER-L or USER-U) mode operation.
D TYPE (DTAT MODE)
Function: Selects the mode and sideband (if appli-
cable) in the DATA mode.
Available Values: RTTY/USR-L/USR-U
Default: RTTY
RTTY: FSK RTTY operation
USR-L: User-programmed custom operation based
on LSB mode
USR-U: User-programmed custom operation based
on USB mode
DIALSTP (DIAL STEP)
Function: Sets the DIAL knob's tuning speed.
Available Values: SSB/CW: 1 / 10 / 20 (Hz)
AM/FM: 100 / 200 (Hz)
Default: SSB/CW: 10 (Hz), AM/FM: 100 (Hz)
The width of the step of the
[
MAIN DIAL
]
knob can
be set for each mode.
DIG VOX
Function: Sets the gain of the VOX circuitry input
level for the DIG mode.
Available Values: OFF / 1~100
Default: OFF
EMERGEN (EMERGENCY)
Function: Enables Tx/Rx operation on the Alaska
Emergency Channel, 5167.5 kHz.
Available Values: ON/OFF
Default: OFF
When this Menu Item is set to “ON,” the spot fre-
quency of 5167.5 kHz will be enabled. To get to this
frequency, use the
[
DSP/SEL
]
knob to navigate. The
Alaska Emergency Channel will be found between
the Memory channel “US5-001” and “MEM-500.”
NOTE:
Use of this frequency is restricted to amateurs oper-
ating in (or within 92.6 km of) the U.S. State of Alaska,
and it is to be used for emergency communications
only (involving the immediate protection of life or prop-
erty).
KEYHOLD (KEY HOLD TIME)
Function: Sets the hold time for a push button to
activate.
Available Values: 0.5 / 1.0 / 1.5 / 2.0
Default: 1.0
MENU MODE
84


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-450D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-450D in the language / languages: English as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info