674732
83
Zoom out
Zoom in
Previous page
1/102
Next page
Page 81FT-450D OPERATION MANUAL
CLAR (CLAR DIAL/SEL)
Function: Setting of CLAR button
Available Values: DIAL / SEL
Default: DIAL
Defines which Control knob is used for setting the
clarifier-offset frequency.
CLK SFT (CLOCK SHIFT)
Function: Shifting of CPU clock frequency
Available Values: ON / OFF
Default: OFF
This function is only used to move a spurious re-
sponse “birdie,” should it fall on a desired frequency.
CONT (DISP CONTRAST)
Function: Display contrast adjustment
Available Values: 1~24
Default: 10
The display contrast level is set 1~24
CW AUTO (CW AUTO MODE)
Function: Enables the KEY jack, to permit CW op-
eration while in SSB modes.
Available Values: OFF / ON
Default: OFF
OFF: The KEY jack is enabled in CW mode only.
ON: The KEY jack is enabled on all modes (SSB
mode: A1A). Thus, on SSB, you can ask a sta-
tion for a CW QSO without having to change
your FT-450’s Mode selection, if Menu “CW
AUTO” is set to “ON.”
CW BFO
Function: Sets the CW carrier oscillator injection
side in CW mode
Available Values: USB / LSB / AUTO
Default: USB
USB: Injects the CW carrier oscillator on the USB
side
LSB: Injects the CW carrier oscillator on the LSB
side
AUTO: Injects the CW carrier oscillator on the LSB
side while operating on the 7 MHz band and
below, USB side while operating on the 10
MHz band and up.
CW DLY (CW DELAY)
Function: Sets the receiver recovery time during
pseudo-VOX CW semi-break-in opera-
tion.
Available Values: FULL / 30~3000ms
Default: 250
The recovery time may be adjusted in steps of 10
msec. A longer delay may be preferable if you pause
frequently while sending.
CW KEY (CW KEY REV)
Function: Sets the keyer paddle's wiring configura-
tion.
Available Values: NOR / REV
Default: NOR
The polarity can be reversed in the menu without
changing the connection of the keyer when there is a
left-handed operator or, two or more people.
NOR(NORMAL): Keyer paddle polarity is normal.
The plug “Tip” connection pro-
duces dots, and the plug "ring" con-
nection produces dashes.
REV(REVERSE): Keyer paddle polarity is inverted.
The plug “Tip” connection pro-
duces dashes, and the “Ring” con-
nection produces dots.
CW QSK
Function: Selects the time delay between when the
key is closed and the carrier is transmit-
ted during QSK operation when using the
internal keyer.
Available Values: 15 / 20 / 25 / 30 (ms)
Default: 15 (ms)
Note:
If you select “25 ms” or “30 ms,” please do not at-
tempt to set Menu “CW SPEED” to a speed faster than
50 wpm (250 cpm), as the delay will make it impos-
sible to transmit.
CWPADDL (CW PADDLE)
Function: When enabled, the microphone’s (MH-
31A8J)
[
UP
]
/
[
DWN
]
keys may be used for
CW keying.
Available Values: KEY / MIC
Default: KEY
KEY: The key connected to KEY Jack is selected.
MIC: When this Menu Item is set to “MIC,” the
microphone’s (MH-31A8J)
[
UP
]
/
[
DWN
]
keys
may be used for CW keying. (while the built-in
electronic keyer is engaged).
CWPITCH
Function: Sets the pitch of the CW sidetone, (BFO
offset) and the CW filter center frequen-
cies.
Available Values: 400 / 500 / 600 / 700 / 800 (Hz)
Default: 700
The CW pitch may be adjusted in steps of 100 Hz.
MENU MODE
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-450D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-450D in the language / languages: English as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info