36011

Yaesu FT-2800 Manual

36
Zoom out
Zoom in
Previous page
1/60
Next page
34 FT-2800M OPERATING MANUAL
The FT-2800M’s scanning capability provides the operator with many convenient methods
of rapid frequency navigation.
BASIC SCANNER OPERATION
Before activating the scanner, make sure that the Squelch is set to silence the background
noise when no signal is present. Scanning is not possible while the Squelch is open (if noise
or signals are being heard).
Scanning may be started or stopped using the microphone’s
[
UP
]
or
[
DWN
]
button. The
following techniques are used for scanning:
r Pressing and holding in either the
[
UP
]
or
[
DWN
]
button for one second in the VFO
mode will cause upward or downward band scanning, respectively, to begin.
r Pressing and holding in either the
[
UP
]
or
[
DWN
]
button for one second in the Memory
mode will cause memory channel scanning toward a higher- or lower-numbered memory
channel, respectively.
r Scanning pauses when a signal opens the squelch, and the decimal point on the display
will blink. You can choose one of three scan-resume modes (described later).
r To halt the scan manually, the easiest way is to push the PTT switch on the microphone
momentarily (no transmission will occur while you are scanning). The scan may also be
halted manually by pressing the microphone’s
[
UP
]
or
[
DWN
]
button, or the
[
D/
MR
(
MW
)]
key.
SCAN-RESUME OPTIONS
Three scan-resume modes are available on the FT-2800M:
r In the “BUSY” mode, the scanner will remain halted for as long as there is carrier present
on the channel; after the carrier drops at the end of the other station’s transmission,
scanning will resume.
r In the “HOLD” mode, the scanner will halt on a signal it encounters. It will not restart
automatically; you must manually re-initiate scanning if you wish to resume.
r In the “5 SEC” mode, the scanner will halt for five seconds only, after which scanning
will resume (whether or not the other station is still transmitting).
The default scan-stop mode is “BUSY.” To change the scan-resume mode, use the following
procedure:
1. Press and hold in the
[
MHz
(
SET
)]
key for one second, then rotate the DIAL knob to
select “23 SCAN.”
2. Press the
[
MHz
(
SET
)]
key, then rotate the DIAL knob to select the desired scan-resume
mode (BUSY/HOLD/5 SEC).
3. Press and hold in the
[
MHz
(
SET
)]
key for one second to save the new setting and exit to
normal operation.
SCANNING
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-2800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-2800 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info