Manual Yaesu FT-2000D (page 20 of 140) (English)

478497

Zoom out

Zoom in

1/140

Page 18 FT-2000D OPERATING MANUAL

FRONT PANEL CONTROLS & SWITCHES

IPO

(

INTERCEPT POINT OPTIMIZATION

)

Switch

This button may be used to set the optimum front end

characteristics of the receiver circuit for a very strong-

signal environment. Available selections are AMP 1

(low distortion amplifier), AMP 2 (2-stage low-distor-

tion RF amplifier), or ON (bypasses the front end RF

amplifier), and the selected receiver RF amplifier ap-

pears at the IPO column of the Receiver Configuration

Indicator in the display.

ADVICE:

The IPO switch affects both the Main (VFO-A) and

Sub (VFO-B) receivers.

R.FLT Switch

This button selects the bandwidth for the Main Band

(VFO-A) receiver’s first IF Roofing Filter. Available

selections are 3 kHz, 6 kHz, 15 kHz, or Auto, and the

selected bandwidth appears in the FLT column of the

Receiver Configuration Indicator on the display.

ADVICE:

 The Roofing Filter selection applies to the Main

band (VFO-A) only.

 Because the roofing filter is in the first IF, the pro-

tection it provides against interference is quite sig-

nificant. When set to AUTO, the SSB bandwidth is

6 kHz, while CW is 3 kHz and FM/RTTY are 15

kHz. On a crowded SSB band, however, you may

wish to select the 3 kHz filter, for the maximum

possible interference rejection.

AGC Switch

This button selects the AGC characteristics for the re-

ceiver. Available selections are FAST, MID, SLOW,

or AUTO, and the “AGC” icon will change according

to the AGC characteristics selected.

Press the

[

AGC

]

button repeatedly to select the de-

sired receiver-recovery time constant. Press and hold

in the

[

AGC

]

button for two seconds to disable the

AGC (for testing or weak-signal reception).

When the

[

AGC

]

button is pressed independently, it

applies to the Main band (VFO-A) receiver.

When you press the

[

]

button, followed by the

[

AGC

]

button (within five seconds of pressing the

[

]

switch),

it affects the Sub band (VFO-B) receiver.

ADVICE:

If the AGC receiver-recovery time is set to “

OffOff

Off” by

pressing and holding in the

[

AGC

]

button, the S-meter

will no longer deflect. Additionally, you will likely en-

counter distortion on stronger signals, as the IF ampli-

fiers and the following stages are probably being over-

loaded.

My FT2000D will not Transmit. Have not used it in over a year. I am sure it is something I have done wrong. Whe u puss PTT the signal goes to ZERO. Please Advise! Submitted on 12-9-2020 at 00:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-2000D in the language / languages: English as an attachment in your email.

The manual is 7,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yaesu FT-2000D Manual

Product: