Manual Yaesu FT-2000D (page 18 of 140) (English)

478497

Zoom out

Zoom in

1/140

Page 16 FT-2000D OPERATING MANUAL

POWER Switch

Press and hold in this switch for one second to turn the

transceiver on. Similarly, press and hold in this switch

for one second to turn the transceiver off. (The FP-

2000’s

[

POWER

]

switch must also be set to on “I”

before this switch will function.)

ADVICE:

 The main power switch for the system is located

on the front panel of the FP-2000 Power Supply.

When the FP-2000 main power switch is pushed

down on the “I” side, the FP-2000 is turned on,

and the FT-2000D is placed in the “standby” state.

If the FP-2000 main power switch is not turned

on, it is not possible to turn on the FT-2000D trans-

ceiver. For more details about the main power

switch location on the FP-2000, please see the dis-

cussion on page 34.

 If you press this switch momentarily while the trans-

ceiver is turned on, the transceiver’s audio will be

muted for three seconds.

MOX Switch

Pressing this button engages the PTT (Push to Talk) cir-

cuit, to activate the transmitter (the LED inside this but-

ton will glow red). It must be turned off (the red LED

will be off) for reception. This button replicates the ac-

tion of the Push to Talk (PTT) switch on the microphone.

When engaging the

[

MOX

]

button (the LED inside this

button glows red) or otherwise causing a transmission to

be started, be certain you have either an antenna or 50-

Ohm dummy load connected to the selected Antenna jack.

TUNE Switch

This is the on/off switch for the FT-2000D’s Auto-

matic Antenna Tuner.

Pressing this button momentarily places the antenna

tuner in line between the transmitter final amplifier and

the antenna jack (“ ” icon will appear in the dis-

play). Reception is not affected.

Pressing and holding in this button for 1/2 second, while

receiving in an amateur band, activates the transmitter

for a few seconds while the automatic antenna tuner

rematches the antenna system impedance for minimum

SWR. The resulting setting is automatically stored in

one of the antenna tuner’s 100 memories, for instant

automatic recall later when the receiver is tuned near

the same frequency.

Pressing this button momentarily, while the Tuner is

engaged, will take the Automatic Antenna tuner out of

the transmit line.

NOTE:

When the Automatic Antenna Tuner is tuning itself, a

signal is being transmitted. Therefore, be absolutely

certain that an antenna or dummy load is connected to

the selected antenna jack before pressing and holding

in the

[

TUNE

]

button to start antenna tuning.

FRONT PANEL CONTROLS & SWITCHES

My FT2000D will not Transmit. Have not used it in over a year. I am sure it is something I have done wrong. Whe u puss PTT the signal goes to ZERO. Please Advise! Submitted on 12-9-2020 at 00:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-2000D in the language / languages: English as an attachment in your email.

The manual is 7,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yaesu FT-2000D Manual

Product: