478497

Yaesu FT-2000D Manual

22
Zoom out
Zoom in
Previous page
1/140
Next page
Page 20 FT-2000D OPERATING MANUAL
FRONT PANEL CONTROLS & SWITCHES
MIC RF PWR Knobs
MIC Knob
The inner
[
MIC
]
knob adjusts the microphone input
level for (non-processed) SSB transmission.
ADVICE:
If you adjust the MIC Gain while speaking in a
somewhat-louder-than-normal voice level, watch
the ALC level and adjust the MIC Gain so that the
ALC reaches just to the right edge of the ALC scale.
Then, when you speak in a more normal voice level,
you’ll be certain not to be over-driving the mic am-
plifier stage.
The Sub band (VFO-B) frequency display will show
the relative microphone gain level for 3 seconds
whenever the outer
[
RF PWR
]
knob is turned.
You may disable this feature (displaying the rela-
tive microphone gain level) via Menu item “015
diSP LVL IND.” See page 117 for details.
RF PWR Knob
The outer
[
RF PWR
]
knob is the main RF Power out-
put control for the transceiver, active in all operating
modes. Clockwise rotation increases the power out-
put. Adjust this control for the desired power output
from the FT-2000D.
ADVICE:
The Sub band (VFO-B) frequency display will show
the RF Power output for 3 seconds whenever the outer
[
RF PWR
]
knob is turned.
You may disable this feature (displaying the RF Power
output) via Menu item “015 diSP LVL IND.” See page
117 for details.
VOX DELAY Knobs
VOX Knob
The inner
[
VOX
]
knob sets the gain of the VOX cir-
cuit, to set the level of microphone audio needed to
activate the transmitter during voice operation while
the
[
VOX
]
switch is engaged. The
[
VOX
]
switch must
be switched “ON” to engage the VOX circuit.
DELAY Knob
The outer
[
DELAY
]
knob sets the hang time of the
VOX circuit for voice operation and keying delay for
CW operation.
During voice operation, this knob sets the hang time,
between the moment you stop speaking, and the auto-
matic switch from transmit back to receive. Adjust this
for smooth VOX operation, so the receiver is only ac-
tivated when your transmission is ended and you wish
to receive.
For CW operation, this knob sets the keying delay,
between the moment you stop sending, and the auto-
matic switch from transmit back to receive during
“Semi-break-in” operation. Adjust this just long enough
to prevent the receiver from being restored during word
spaces at your preferred sending speed.
ADVICE:
The Sub band (VFO-B) frequency display will show
the hang time of the VOX circuit for 3 seconds when-
ever the outer
[
DELAY
]
knob is turned.
You may disable this feature (displaying the hang time
of the VOX circuit) via Menu item “015 diSP LVL
IND.” See page 117 for details.
… 22 …


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ft-2000d

Reset search

  • My FT2000D will not Transmit. Have not used it in over a year. I am sure it is something I have done wrong. Whe u puss PTT the signal goes to ZERO. Please Advise! Submitted on 12-9-2020 at 00:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-2000D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-2000D in the language / languages: English as an attachment in your email.

The manual is 7,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info