478463
61
Zoom out
Zoom in
Previous page
1/90
Next page
57FT-1900R OPERATING MANUAL
The ARTS™ feature uses DCS signaling to inform both parties when you and another
ARTS™-equipped station are within communications range. This may be particularly use-
ful during Search-and Rescue situations, where is important to stay in contact with other
members of your group.
Both stations must set up their DCS codes to the same code number, then activate their
ARTS™ feature using the command appropriate for their radio. Alert ringers may be acti-
vated, if desired.
Whenever you push the PTT switch, or every 25 (or 15) seconds after ARTS™ is activated,
your radio will transmit a signal which includes a (subaudible)
DCS signal for about 1 second. If the other radio is in range,
the beeper will sound (if enabled) and the display will show
IN RNG” as opposed to the out of range display “OUTRNG
in which ARTS™ operation begins.
Whether you talk or not, the polling every 15 or 25 seconds will continue until you de-
activate ARTS™. Every 10 minutes, moreover, you can have your radio transmit your callsign
via CW, so as to comply with identification requirements. When ARTS™ is de-activated,
DCS will also be deactivated (if you were not using it previously in non-ARTS™ operation).
If you move out of range for more than one minute (four pollings), your radio will sense
that no signal has been received, three beeps will sound, and the display will revert to
OUTRNG.” If you move back into range, your radio will again beep, and the display will
change back to the “IN RNG” indication.
During ARTS
operation, your operating frequency will continue to be displayed, but no
changes may be made to it or other settings; you must terminate ARTS
in order to resume
normal operation. This is a safety feature designed to prevent accidental loss of contact due
to channel change, etc.
Basic ARTS
Setup and Operation
1. Assign the ARTS™ feature to the microphone’s programmable button
([
P1
]
,
[
P2
]
,
[
P3
]
,
or [
P4
])
, per the discussion on page 65.
2. Set your radio and the other radio(s) to the same DCS code number, per the discussion
on page 25.
3. Press the assigned microphone’s
programmable button momentarily
. You will observe
the “OUTRNG” display on the LCD. ARTS™ operation
has now commenced.
4. Every 25 seconds, your radio will transmit a “polling” call to the other station. When
that station responds with its own ARTS™ polling signal, the display will change to
IN RNG” to confirm that the other station’s polling code
was received in response to yours.
ARTS™
(
AUTOMATIC RANGE TRANSPONDER SYSTEM
)
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-1900R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-1900R in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info