478463

Yaesu FT-1900R Manual

63
Zoom out
Zoom in
Previous page
1/90
Next page
59FT-1900R OPERATING MANUAL
CW Identifier Setup
The ARTS™ feature includes a CW identifier, as discussed previously. Every ten minutes
during ARTS™ operation, the radio can be instructed to send “DE (your callsign) K,” if this
feature is enabled. The callsign field may contain up to 16 characters.
Here’s how to program the CW Identifier:
1. Press and hold in the
[
MHz
(
SET
)]
key for one second, then
rotate the DIAL knob to select “11 CW ID.”
2. Press the
[
MHz
(
SET
)]
key, followed by the
[
LOW
(
A/N
)]
key, to display any previ-
ously-stored callsign.
3. Press and hold in the
[
LOW
(
A/N
)]
key for one second to
Clear any previous callsign.
4. Rotate the DIAL knob to select the first letter/number of
your callsign, then press the
[
LOW
(
A/N
)]
key momentarily
to save the first letter/number and move on to the next character.
5. Repeat the previous step, as many times as necessary, to complete your callsign. Note
that the “slant bar” (–
•
•
–
•
) is among the available charac-
ters, should you be a “portable” station.
6. If you make a mistake, press the
[
REV
(
DW
)]
key to move back to the previous letter/
number’s slot, then re-select the correct letter/number.
7. When you have finished entering your entire callsign and it contains less than 16 char-
acters, press the
[
MHz
(
SET
)]
key momentarily to confirm the callsign. (if you callsign
has exactly 16 characters, you do not need to press the
[
MHz
(
SET
)]
key in this step,
and step ).
8. Press the
[
MHz
(
SET
)]
key momentarily again, then rotate
the DIAL knob to set this Item to “ON” (to enable the CW
ID function).
9. When you have made your selection, press and hold in the
[
MHz
(
SET
)]
key for one
second to save the new setting and exit to normal operation.
To disable the CW Identifier:
1. Press and hold in the
[
MHz
(
SET
)]
key for one second, then
rotate the DIAL knob to select “11 CW ID.”
2. Press the
[
MHz
(
SET
)]
key momentarily, then rotate the
DIAL knob to set this Item to “OFF” (to disable the CW ID
function).
3. When you have made your selection, press and hold in the
[
MHz
(
SET
)]
key for one
second to save the new setting and exit to normal operation.
You may check your work by monitoring the entered callsign. To do this, recall
Set Mode Item “11 CW ID” and press the [MHz(SET)] key, then press the [D/
MR(MW)] key.
ARTS™
(
AUTOMATIC RANGE TRANSPONDER SYSTEM
)
… 63 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-1900R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-1900R in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info