797325

XPR DINMTPX-MF-SA Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
www.xprgroup.com
6
NL
DE
ES
IT
IT DE
ES NL
FR
FR
EN
EN
1. Close the Jumper. DINRTT beeps continuously and
the red led blinks.
2. Open the Jumper
3. Wait for Beep + OK Beep (short + short + long beep)
4. After the OK beep, the coupling is done.
1. Close the jumper on the back of the device.
2. Wait for multiple short beeps + Red LED blinks.
3. Open the jumper. (short beeps will stop)
4. Wait for Green LED blink + beep.
Warning: Reset procedure will clear the device from Hotel or Access Software
and it will delete the configuration, the events and the blacklisted cards.
Warning: This procedure will unpair the connected relay unit (RTT, DINRTT or RU2)
1. Chiudere il ponticello. Il DINRTT emette segnali
acustici in modo continuo e il LED rosso lampeggia.
2. Aprire il ponticello
3. Attendere il segnale acustico + il segnale acustico di OK
(suono breve + suono breve + suono lungo)
4. Dopo il segnale acustico di OK, l’accoppiamento è pronto.
1. Chiudere il ponticello sul retro del dispositivo.
2. Attendere l’emissione di più segnali acustici brevi + lampeggiamento del LED rosso.
3. Aprire il ponticello. (l’emissione dei segnali acustici brevi si interrompe)
4. Attendere il lampeggiamento del LED verde + segnale acustico.
Avvertenza:
la procedura di reset elimina il dispositivo dal software Hotel o Access e
cancella la configurazione, gli eventi e le schede incluse nella blacklist.
Avvertenza:
con questa procedura si scollega l’unità relè accoppiata (RTT, DINRTT o RU2)
1. Schließen Sie die Steckbrücke auf der Rückseite des Geräts.
2. Mehrere kurze Piepstöne + rote LED blinkt.
3. Öffnen Sie die Steckbrücke (die kurzen Piepstöne hören auf)
4. Grüne LED blinkt + Piepston.
Warnung:
Das Zurücksetzen löscht die Hotel oder Access Software vom Gerät,
ebenso wie die Konfigurierung, sämtliche Ereignisse und die gesperrten Karten.
Warnung:
Dieser Vorgang entkoppelt die angeschlossene Relais-Einheit (RTT, DINRTT oder RU2)
1. Cerrar el puente en la parte posterior del dispositivo.
2. Esperar varios pitidos cortos + parpadeo del LED rojo.
3. Abrir el puente. (los pitidos cortos se interrumpirán)
4. Esperar el parpadeo del LED verde + pitido.
Advertencia: Con el procedimiento de restablecimiento se borrará del dispositivo
el software del Hotel o del Acceso, y se eliminarán la configuración, los eventos y las
tarjetas de la lista negra.
Advertencia: Este procedimiento desacoplará la unidad de relé conectada
(RTT, DINRTT o RU2)
1. Sluit de jumper aan de achterkant van het apparaat.
2. Wacht tot u meerdere korte tonen hoort + rode led knippert.
3. De jumper openen (de korte tonen stoppen)
4. Wacht tot de groene led knippert + toon.
Waarschuwing:
De reset-procedure wist het apparaat uit de hotel- of toegangssoftware
en wist de configuratie, de gebeurtenissen en de kaarten op de zwarte lijst.
Waarschuwing: Met deze procedure zal de aangesloten relaiseenheid (RTT, DINRTT
of RU2) worden ontkoppeld.
1. Schließen Sie die Steckbrücke. DINRTT piepst
kontinuierlich und die rote LED blinkt.
2. Öfnen Sie die Steckbrücke
3. Auf Piepton warten + Piepton OK (2 x kurzer + 1 x langer Piepton)
4. Nach dem Piepton OK, ist die Kopplung erfolgt.
1. Ponga el puente en la posición cerrada. DINRTT emitirá un
pitido continuo y el LED rojo parpadeará.
2. Ponga el puente en la posición abierta.
3. Espere a que suene un pitido + pitido de OK (dos pitidos cortos más
uno largo).
4. Después del pitido de OK, el acoplamiento está realizado.
1. De jumper sluiten. DINRTT piept continu en de rode
led knippert.
2. De jumper openen
3. Wacht op een pieptoon + OK-signaal (korte + korte +
lange toon)
4. Koppeling vindt plaats na het OK-signaal.
1. Fermer le cavalier. DINRTT émet un bip sonore
continu et la LED rouge clignote.
2. Ouvrir le cavalier
3. Attendre le bip + bip Ok (bip court + court + long)
4. Après le bip Ok, le couplage est efectué.
1. Éteindre le cavalier au dos de l’appareil.
2. Attendre plusieurs petits bips + jusqu’à ce que la LED rouge clignote.
3. Ouvrir le cavalier (les bips brefs cesseront)
4. Attendre le clignotement de la LED verte + un bip.
Avertissement :
Réinitialiser la procédure supprimera l’appareil du logiciel hôtelier ou le logiciel
d’accès et il efacera la configuration, les évènements et les cartes inscrites sur liste noire.
Avertissement :
Cette procédure séparera l’unité de relais connectée (RTT, DINRTT ou RU2)
PAIRING READER WITH DINRTT/ASSOCIATION DU LECTEUR ET DE DINRTT/ACCOPPIAMENTO DEL LETTORE CON IL DINRTT/
VINCULACIÓN DEL LECTOR A DINRTT/VERBINDEN DES LESERS MIT DINRTT/LEZER KOPPELEN MET DINRTT
RESET THE READER/ RÉINITIALISER LE LECTEUR/ RESET DEL LETTORE/
RESTABLECER EL LECTOR/ LESER ZURÜCKSETZEN/ RESET DE LEZER
Relay 2 for energy management (to power switch)
Relais 2 pour la gestion de l’énergie (vers interrupteur)
Relè 2 per la gestione energetica (per interruttore di alimentazione)
Relé 2 para gestión de la energía (al interruptor de alimentación)
Relais 2 für Energieverwaltung (zum Netzschalter)
Relais 2 voor energiebeheer (naar stroomschakelaar)
J1
Reset Procedure/ Réinitialiser la procédure/ Procedura di reset/Procedimiento
de restablecimiento/ Rücksetzverfahren (RESET) / Reset-procedure
Max 150m
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for XPR DINMTPX-MF-SA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of XPR DINMTPX-MF-SA in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info