Manual Worx WX523 (page 12 of 19) (English, German, Dutch, French, Italian, Polish, Spanish)

575058

Zoom out

Zoom in

1/19

20V WORX saw EN

for the equipment.

n) Keep cells and battery pack clean and dry.

o) Wipe the cell or battery pack terminals with

a clean dry cloth if they become dirty.

p) Secondary cells and battery pack need

to be charged before use. Always use

the correct charger and refer to the

manufacturer’s instructions or equipment

manual for proper charging instructions.

q) Do not leave a battery pack on prolonged

charge when not in use.

r) After extended periods of storage, it may

be necessary to charge and discharge the

cells or battery pack several times to obtain

maximum performance.

s) Secondary cells and battery pack give their

best performance when they are operated

at normal room temperature (20 °C ± 5 °C).

t) Retain the original product literature for

future reference.

u) Use only the cell or battery pack in the

application for which it was intended.

v) When possible, remove the battery pack

from the equipment when not in use.

w) Dispose of properly.

SAFETY INSTRUCTIONS

FOR ABRASIVE CUTTING-

OFF OPERATIONS

CUT-OFF MACHINE SAFETY WARNINGS

a) The guard provided with the tool must

be securely attached to the power

tool and positioned for maximum

safety, so the least amount of wheel

is exposed towards the operator.

Position yourself and bystanders away

from the plane of the rotating wheel.

The guard helps to protect operator from

broken wheel fragments and accidental

contact with wheel.

b) Use only diamond cut-off wheels

for your power tool. Just because an

accessory can be attached to your power

tool, it does not assure safe operation.

C) The rated speed of the accessory

must be at least equal to the

maximum speed marked on the power

tool. Accessories running faster than their

rated speed can break and ﬂy apart.

d) Wheels must be used only for

recommended applications. For

example: do not grind with the side of

cut-off wheel. Abrasive cut-off wheels

are intended for peripheral grinding, side

forces applied to these wheels may cause

them to shatter.

e) Always use undamaged wheel ﬂanges

that are of correct diameter for your

selected wheel. Proper wheel ﬂanges

support the wheel thus reducing the

possibility of wheel breakage.

f) Do not use worn down reinforced

wheels from larger power tools.

Wheels intended for a larger power tool

are not suitable for the higher speed of a

smaller tool and may burst.

g) The outside diameter and the

thickness of your accessory must

be within the capacity rating of your

power tool. lncorrectly sized accessories

cannot be adequately guarded or

controlled.

h) The arbour size of wheels and ﬂanges

must properly ﬁt the spindle of

the power tool. Wheels and ﬂanges

with arbour holes that do not match the

mounting hardware of the power tool will

run out of balance, vibrate excessively and

may cause loss of control.

i) Do not use damaged wheels. Before

each use, inspect the wheels for chips

and cracks. If power tool or wheel is

dropped, inspect for damage or install an

undamaged wheel. After inspecting and

installing the wheel, position yourself and

bystanders away from the plane of the

rotating wheel and run the power tool at

maximum no load speed for one minute.

Damaged wheels will normally break apart

during this test time.

j) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety

glasses. As appropriate, wear dust mask,

hearing protectors, gloves and shop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection

must be capable of stopping ﬂying debris

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX523 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX523 Manual

Product: