Manual Worx WX523 (page 14 of 19) (English, German, Dutch, French, Italian, Polish, Spanish)

575058

Zoom out

Zoom in

1/19

20V WORX saw EN

diamond wheel with a peripheral

gap greater than 10 mm or toothed

saw blade. Such blades create frequent

kickback and loss of control.

f) Do not “jam” the wheel or apply

excessive pressure. Do not attempt

to make an excessive depth of cut.

Overstressing the wheel increases the

loading and susceptibility to twisting or

binding of the wheel in the cut and the

possibility of kickback or wheel breakage.

g) When wheel is binding or when

interrupting a cut for any reason,

switch off the power tool and hold the

power tool motionless until the wheel

Comes to a complete stop. Never

attempt to remove the wheel from the cut

while the wheel is in motion otherwise

kickback may occur. lnvestigate and take

corrective action to eliminate the cause of

wheel binding.

h) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

i ) Support panels or any oversized

workpiece to minimize the risk of

wheel pinching and kickback. Large

workpieces tend to sag under their own

weight. Supports must be placed under the

workpiece near the line of cut and near the

edge of the workpiece on both sides of the

wheel.

j) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical

wiring or objects that can cause kickback.

GENERAL SAFETY

WARNINGS FOR YOUR

LASER

WARNING: Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result in

serious injury.

Save all warnings and instructions for

future reference.

These lasers do not normally present an

optical hazard although staring at the

beam may cause ﬂash blindness.

Do not stare directly at the laser beam. A

hazard may exist if you deliberately stare

into the beam, please observe all safety

rules as follows:

1) The laser shall be used and maintained

in accordance with the manufacturer’s

instructions.

2) Never aim the beam at any person or

an object other than the work piece.

3) The laser beam shall not be

deliberately aimed at another person

and shall be prevented from being

directed towards the eye of a person

for longer than 0.25 seconds area.

4) Always ensure the laser beam is

aimed at a sturdy work piece without

reﬂective surfaces, e.g. wood or

rough-coated surfaces are acceptable.

Bright shiny reﬂective sheet steel or similar

is not suitable for laser applications as the

reﬂective surface may direct the laser beam

back at the operator.

5) Do not change the laser device with

a different type. The manufacturer or an

authorized agent must carry out repairs.

6) CAUTION: Use of controls or adjustments

other than those speciﬁed herein may

result in hazardous radiation exposure.

ADDITIONAL SAFETY WARNING FOR

CLASS 2 LASER

The laser device ﬁtted to this tool is CLASS

2 with a maximum radiation of 1.5mW and

650nm wavelength.

CLASS 2 LASER RADIATION, DO NOT

STARE INTO BEAM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX523 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX523 Manual

Product: