Manual Worx WG368E.9 (page 15 of 204) (English, German, Dutch, French, Italian, Polish, Spanish)

576045

Zoom out

Zoom in

1/204

Cordless Chain Saw EN

TENSIONING CHAIN

New saw chains will stretch. Check chain

tension frequently when ﬁrst used and tighten

when Chain becomes loose around the Guide

Bar (7).

WARNING: Remove the battery

from the tool before adjusting saw

chain tension.

WARNING: Cutting edges on chain

are sharp. Use protective gloves

when handling chain.

WARNING: Maintain proper chain

tension always. A loose chain will

increase the risk of kickback. A loose

chain may jump out of guide bar groove.

This may injure operator and damage

chain. A loose chain will cause chain,

bar, and sprocket to wear rapidly.

1. Place the chain saw on any suitable ﬂat

surface.

2. Turn the Chain Tensioning Knob (10)

clockwise until it is hand tight. The tension

is automatically set while the Chain

Tensioning Knob is being tightened.

The ratchet mechanism (a) prevents the

chain tension from loosening. (See Fig. F1)

3. Double check the tension set by the

automatic Chain Tensioning Knob. The

correct chain tension is reached when the

Chain (8) can be raised approx. 3-6mm

from the Guide Bar (7) in the center (the

chain links should just remain in the bar

track). This should be done by using one

hand to raise the chain against the weight

of the machine. (See Fig. F2)

Use a screwdriver to move chain around

Guide Bar to ensure kinks do not exist. The

chain should rotate freely. (See Fig. F3 )

4. When the chain looses, unscrew the Chain

Tensioning Knob absolutely and then

Screw on the cover plate with the locking

knob tightly again.

LUBRICATION

IMPORTANT: He chain saw is

not supplied ﬁlled with oil. It is

essential to ﬁll with oil before use. Never

operate the chain saw without chain

oil or at an empty oil tank level, as this

will result in extensive damage to the

product.

NOTE: Chain life and cutting capacity depend

on optimum lubrication. Therefore, the chain

is automatically oiled during operation.

Filling oil tank:

1. Set chain saw on any suitable surface with

Oil Filler Cap (4) facing upward.

2. Clean area around the Oil Filler Cap with

cloth unscrew cap.

3. Add bar and chain oil until reservoir is full.

ISO VG32 Bar and chain oil of any brand

can be used.

4. Avoid dirt or debris entering oil tank, reﬁt

the Oil Filler Cap and tighten.

IMPORTANT: To allow venting of

the oil reservoir, small breather

channels are provided between the oil

ﬁller cap and the strainer, to prevent

leakage ensure machine is left in a

horizontal position (Oil Filler Cap (4)

uppermost) when not in use.

It is important to use only the

recommended oil to avoid damage to the

chain saw. Never use recycled/old oil.

Use of non approved oil will invalidate

the warranty.

CHECKING THE AUTOMATIC OILER

Proper functioning of the automatic oiler can

be checked by running the chain saw and

pointing the tip of the Guide Bar (7) towards a

piece of cardboard or paper on the ground.

If an increasing oil pattern develops on the

cardboard, the automatic oiler is operating

ﬁne. If there is no oil pattern, despite a full

oil reservoir, contact WORX customer service

agent or WORX approved service agent.

CAUTION: Do not touch the ground

with the chain. Ensure safety clearance

of 30cm.

OPERATION

1. BEFORE USING YOUR CORDLESS

TOOL

ATTENTION: The charger and

battery pack are specially designed

to work together so do not attempt to

use any other devices. Never insert or

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WG368E.9 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 8,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WG368E.9 Manual

Product: