Manual Worx WG368E.9 (page 16 of 204) (English, German, Dutch, French, Italian, Polish, Spanish)

576045

Zoom out

Zoom in

1/204

Cordless Chain Saw EN

allow metallic objects into your charger

or battery pack connections because

of an electrical failure and hazard will

occur.

NOTE: Your battery pack is UNCHARGED and

you must charge once before use.

The battery charger supplied is matched to

the Li-Ion battery installed in the machine. Do

not use another battery charger.

2. CHARGING YOUR BATTERY PACK

The Li-ion battery is protected against deep

discharging. When the battery is empty,

the machine is switched off by means of a

protective circuit.

In a warm environment or after heavy use, the

battery pack may become too hot to permit

charging. Allow time for the battery to cool

down before recharging.

3. TO REMOVE OR INSTALL BATTERY

PACK (See Fig. G)

Depress the Battery Pack Release Button to

remove the Battery Pack from your tool. After

recharging, insert the Battery Pack into battery

port (See Fig. G). A simple push and slight

pressure will be sufﬁcient until a click is heard.

Check to see if the battery is fully secured.

NOTE: When removing the battery pack,

hold it ﬁrmly to avoid dropping and

injury.

4. BATTERY STATUS LED’S (See Fig. H)

NOTE: The Status LED’s will indicate the

battery condition when the button on

the battery is pressed.

The LED’s constantly senses and displays the

battery condition as follows:

Press the button “POWERTEST”, the light

button is illuminated.

When the three green lights are illuminated,

the battery is in a highly charged condition.

When two lights ( ) are illuminated, the

battery is in a moderately charged condition.

When only one green light ( ) is illuminated,

the battery charge is depleted.

IMPORTANT: When only one light is

illuminated, your battery is overly

discharged, even though the tool may

still be capable of working. Continuing

to operate your tool with the battery in

this discharged condition may reduce

the life and performance of your battery.

5. SWITCHING ON AND OFF (See Fig. I)

For switching on the machine, press the

Lock-off Button (3), then fully press the On/Off

Switch (2) and hold in this position. The Lock-

Off Button (3) can now be released.

For switching off, release the On/Off Switch (2).

Cutting

IMPORTANT: Is the oil reservoir

ﬁlled? Check the Oil Level Window

(18) prior to starting and regularly

during operation. Reﬁll oil when oil level

is low. A full oil tank will last approx. 20

minutes depending on sawing intensity

and stops (See Fig. J).

Check recent replaced chain tension

about every 10 minutes during

operation.

1. Install the battery pack into the machine

(See Fig. G).

2. Make sure section of log to be cut is not

laying on the ground. This will keep the

Chain (8) from touching the ground as it

cuts through the log. Touching the ground

while the Chain is moving is dangerous

and will dull the Chain.

3. Use both hands to grip saw. Always use

left hand to grip front handle and right

hand to grip rear handle. Use a ﬁrm grip.

Thumbs and ﬁngers must wrap around

saw handles (See Fig. K).

4. Make sure your footing is ﬁrm. Keep feet

shoulder width apart. Divide your weight

evenly on both feet.

5. When ready to make a cut, push the

Lock-off Button (3) completely in with the

right thumb and squeeze the trigger. This

will turn the saw on. Releasing the trigger

will turn the saw off. Make sure the saw is

running at full speed before starting a cut.

6. When starting a cut, slowly place the

moving chain against the wood. Hold saw

ﬁrmly in place to avoid possible bouncing

or skating (sideways movement) of saw.

7. Guide the saw using light pressure and

do not put excessive force on the saw. The

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WG368E.9 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 8,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WG368E.9 Manual

Product: