724649
13
Zoom out
Zoom in
Previous page
1/18
Next page
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018
24 25
B. Contact Firing
1. Once the single/contact ring slider knob (9) is set to contact ring,
depress the trigger switch (6) (Fig U), and then depress the safety striker
pin ush on the contact surface to re a single nail / staple (Fig T).
2. Keeping your nger pressed on the trigger switch (6), lift the Brad
nailer / stapler away from the contact surface, hence also releasing the
safety striker pin (1), and place in the next position for the next nail or
staple to be red, again depressing the safety striker pin ush onto the
contact surface. The Brad nailer / stapler will automatically re another
staple or nail again (Fig V).
3. Repeat the process keeping your nger pressed on the trigger switch
(6), to continually re each nail/staple.
NOTE: The safety striker pin (1) MUST be depressed at the same time as
continually pressing the trigger switch (6), otherwise the Brad nailer /
stapler will not re / function.
WARNING: Do not keep the trigger switch (6) depressed when
the tool is not in use to prevent accidental ring.
Using the LED Worklight/s while using the
Brad Nailer / Stapler
CAUTION! LED is laser class 1! Do not look directly into the laser as this
may result in damage to the eyes.
1. To turn on the LED worklights while on the Brad nailer / stapler, press
on the LED worklight switch (7) before pressing on the trigger switch
(6) (Fig W/X).
Removing jammed Nails / Staples
1. If the LED battery and function indicator (10) is ashing red (Fig N)
this indicates a jam in the magazine.
2. Remove the battery from the Brad nailer / stapler.
3. Open the magazine by pressing on the magazine release latch (14)
(Fig Y), and remove the nail or staple cartridge and the jammed nail or
staple (Fig Z).
4. Re-install nails or staples, re-install battery, and check the jam is
corrected. If corrected, the red light will be no longer ashing on the
LED battery and function indicator (10).
5. If the jam is still not corrected it means a nail or staple may be jammed
in the internal striking mechanism.
6. Remove the battery from the Brad nailer / stapler, then using the
supplied 3mm hex key (19), remove the 4 x hex screws located in front
of the depth adjustment wheel and remove the nosepiece. Remove the
jammed nail / staple; this may require using pliers (Fig AA).
7. When the jam is removed, reattach the nose
piece and resecure the 4 x hex screws using
the supplied 3mm hex key (19). Re-install nails
or staples, re-install battery, and check the jam
is corrected. If corrected, the red light will be
no longer ashing on the LED battery and
function indicator (10).
V. W. X.
Y.
Z. AA.
JAM
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone TG212T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone TG212T in the language / languages: English as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info