724649
12
Zoom out
Zoom in
Previous page
1/18
Next page
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018
22 23
Operation
Checking the LED Battery and
function indicator
WARNING: Always keep the tool pointed
away from yourself and others when in
use. Failure to do so could result in possible
serious personal injury.
1. After installing the nail / staple cartridge into
the magazine, install your purchased fully
charged Xnity battery onto the brad nailer/
stapler per instructions on pages 19/20.
2. Check there are no lights lit up on the LED
battery and function indicator (10). If you have
loaded the nails or staples correctly, and the
battery is fully charged, no lights will be on.
3. If the LED battery and function indicator (10) is
ashing red this indicates there is a jam in the
magazine (Fig N). Refer to page 25 for xing
jams.
4. If the LED battery and function indicator (10) is
red, this indicates the battery is low on charge
(Fig O). Charge your purchased Xnity battery.
5. If the LED battery and function indicator (10)
is ashing green (Fig P), this indicates the brad
nailer / stapler has overheated. Refer to page
26 for further instruction.
6. If the LED Battery and function indicator (10)
is green (Fig Q), there are no nails/ staples
installed. Refer to pages 19/20 for installing
nails / staples.
Setting the Single or Contact Firing
Function
1. To set the ring function to single shots, slide
the single/contact ring slider knob (9) to the
left (Fig R). Single ring is suitable for precise
single nail / staple placement.
2. To set the ring function to multiple contact
shots, slide the single/contact ring slider
knob (9) to the right (Fig S). Continual contact
ring is good for quick and multiple nail /
staple ring.
A. Single Firing
1. Once the single/contact ring slider knob (9)
is set to single ring, depress the safety striker
pin ush on the contact surface (Fig T), and
then press the trigger switch (6) to re a single
nail or staple (Fig U).
2. Release the trigger switch (6), and lift the brad
nailer / stapler away from the contact surface,
hence also releasing the safety striker pin (1).
3. Repeat the process for single ring of
individual nails or staples.
NOTE: The safety striker pin (1) MUST be
depressed at the same time as pressing the
trigger switch (6), otherwise the Brad nailer /
stapler will not re / function.
Q. U.
P. T.
O. S.
N. R.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone TG212T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone TG212T in the language / languages: English as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info