724638

Workzone S1B-DW01 Manual

9
Zoom out
Zoom in
Previous page
1/15
Next page
220W 3-in-1 Multi Purpose Sander
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: S1B-DW01-220W • 09/2018 • 61865
(toll free)
AFTER SALES SUPPORT
(toll free)
220W 3-in-1 Multi Purpose Sander
e-mail: help@powertoolsupport.com1800 909 909
MODEL No.: S1B-DW01-220W • 09/2018 • 61865
14 15
Assembly Preparation
It is best to make a trial run on a scrap piece of material to determine the
optimum grades of sandpaper for a particular job. If there are still marks
on your work after sanding, try either going back to a coarser grade and
sanding the marks out before recommencing with the original choice of
grit, or try using a new piece of sandpaper to eliminate the unwanted marks
before going on to a ner grit and nishing the job.
Fitting / Attaching the sanding sheet
WARNING! Always remove the plug from the mains power socket
before carrying out any work on the sander.
NOTE: Before tting a new sanding sheet, remove any dust and dirt from the
sander plate.
Attaching sanding sheets using Velcro:
NOTE: Make sure the holes on the sandpaper are aligned with the holes on
the sander base plate. This ensures maximum dust removal and allows air
ow from the motor.
1. Attach the sanding sheet to the tted sander
plate by simply applying the underside of the
sandpaper onto the velcro base (Fig J). This
type of sandpaper is “hook and loop”, and the
velcro holds the sanding sheet in place.
2. To remove the sanding sheet, simply pull the
sanding sheet o the sander plate (Fig K).
Preparation
Fitting/changing the sander plates –
Random Orbital Sander Plate
WARNING! Always remove the plug from the mains power socket
before carrying out any work on the sander.
Changing from the tted rectangle sander plate (9) to the Random Orbital
Sander plate (13).
1. Using a philips head screwdriver (not supplied),
remove the four screws (12) visible on the
underside of the rectangle sander plate (9)
in an anti-clockwise direction (Fig A).
2. Once the 4 screws are all loose, remove the
pre-tted rectangle sander plate (9) (Fig B).
3. The random orbital sander plate (13) only
requires xing of the 4 x screws, and does not
require the rubber pins to be used.
4. Align the screw holes on the random orbital
sander plate (13) underside (non Velcro side),
with the threaded holes on the sander drive
plate (Fig H).
5. Using 4 x screw + washers from either of the
other sander plates (9) / (11), secure the random
orbital sander plate (13) onto the sander drive
plate by screwing in a clockwise direction (Fig I).
K.
J
H.
I.
TIGHTEN
Selecting the suitable sanding sheet
The material removal rate and surface quality are determined by the grain
strength of the sandpaper. Ensure you use a suitable grit (g) of sandpaper
for working on dierent materials. The 80 grit (g) sandpaper supplied is
used for more coarse / rougher sanding / removal. The 240 grit (g) is better
suited for detail and ne sanding. This sander includes an 80g and 240g
sandpaper sheet for each sander plate base.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone S1B-DW01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone S1B-DW01 in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info