724638
8
Zoom out
Zoom in
Previous page
1/15
Next page
220W 3-in-1 Multi Purpose Sander
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: S1B-DW01-220W • 09/2018 • 61865
(toll free)
AFTER SALES SUPPORT
(toll free)
220W 3-in-1 Multi Purpose Sander
e-mail: help@powertoolsupport.com1800 909 909
MODEL No.: S1B-DW01-220W • 09/2018 • 61865
12 13
5. To t the triangular sander plate (11), rst
ensure the tip of the plate points forwards
(Fig D).
6. Using the additional supplied 4 x rubber pins
(15), prepare the base by inserting the
4 x rubber pins into the 4 x holes on the
triangular sander plate (Fig E).
7. Ensure that the sander drive plate on the
sander is aligned with the triangular sander
plate such that the threaded holes of the
sander drive plate are aligned with the
mounting holes on the triangular sanding plate
(11) (Fig F).
8. Push the triangular sander plate (11) on to the
sander drive plate so the rubber pins engage
with the holes on the sander housing, and
using the 4 x screws + washers supplied in
a separate bag, screw them in to secure the
triangular sander plate into place onto the
sander drive plate (Fig G).
9. Ensure the screws are tightened before use.
There is no pre-assembly required, other than tting the base required
for rst use. The Sander is tted with the rectangle sander plate (9). For
changing the sander plate to the triangular sanding plate (11), or the
random orbit sanding plate (13), refer to the following instructions.
Fitting/changing the sander plates – Triangular Sander Plate
Changing from the tted rectangle sander plate (9) to the triangular sander
plate (11).
WARNING! Always remove the plug from the mains power socket
before carrying out any work on the sander.
1. Always use the appropriate sander plate (9) / (11) / (13) for the correct
application required.
2. Using a philips head screwdriver (not supplied), remove the four screws
(12) visible on the underside of the rectangle sander plate (9) in an
anti-clockwise direction (Fig A).
3. Once the 4 screws are all loose, remove the pre-tted rectangle sander
plate (9) (Fig B).
4. For re-tting the rectangle sander plate (9), follow the instructions in
reverse order.
NOTE: The rectangle sander plate (9) can only be tted to the sander in
one direction. Please pay attention to the arrow marks on the rectangle
sander plate (9) when doing this. These must point forwards (Fig C).
Assembly Assembly
Assembly
C.A. B.
F.
D.
E.
G.
LOOSEN
TIGHTEN
4 X
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone S1B-DW01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone S1B-DW01 in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info