724664
12
Zoom out
Zoom in
Previous page
1/22
Next page
Jawzilla Portable Clamping Jaws
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. JH1000-01 • 03/2016 • 52539
(toll free)
10
AFTER SALES SUPPORT
(toll free)
Jawzilla Portable Clamping Jaws
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. JH1000-01 • 03/2016 • 52539
Clamping your work piece
WARNING: Do not overload the clamping jaws beyond its rated capacity.
Prior to using the portable clamping jaws ensure it is located on a flat and
level surface where all three legs are touching the ground.
1. Ensure that the clamp locking lever (11) is in the unlock position (Fig J).
2. Using the rail push handle (1) extend the sliding clamp rail (2) away
from the fixed clamping jaw (12) allowing you to fit the material you are
clamping within the fixed clamping jaw (12) and the moving clamping jaw
(13) (Fig K), then place your clamping material in between the 2 jaws (Fig L).
3. To lock the clamping material in between the fixed clamping jaw (12) and
the moving clamping jaw (13), push down the clamp locking lever (11) to
the locking position (Fig M), then using your foot, push down the clamp
foot pedal (8) to fully secure the clamping material in place (Fig N)
NOTE: Ensure your clamping material / work piece is secured in the
clamping stand before commencing any work.
WARNING: Stop immediately if the clamping material /work piece or the
clamping jaws move when operating.
WARNING: Be aware of overbalancing.
When a large piece is cut from one end of job, always ensure the work piece
is well supported to avoid dropping and tilting danger.
Un-Clamping your work piece
1. Push up the clamp locking lever (11) to the unlock position (Fig J).
2. Using your foot, push down on the clamp foot pedal (8) to release the
clamping material being locked in place (Fig N). The clamping material /
work piece can now be removed from the clamping jaws.
L.K.J.
Clamping
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone JH1000-01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone JH1000-01 in the language / languages: English as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info