724636
10
Zoom out
Zoom in
Previous page
1/21
Next page
Digital Inverter Generator with Pure Sine Wave
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. EP2800i • 09/2018 • 62007
(toll free)
AFTER SALES SUPPORT
(toll free)
Digital Inverter Generator with Pure Sine Wave
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. EP2800i • 09/2018 • 62007
16 17
Indicators
This generator has three main LED indicators to indicate to the operator
various conditions as follows:
1. Low oil indicator (Fig D)
The low oil indicator light (4) is a
yellow LED and will illuminate when
the oil level of the generator is too
low. The generator will stop operating
within 10 seconds if the yellow
light comes on. The yellow LED will
illuminate when the generator is being attempted to start if the oil is low, i.e.
when the cord is being pulled, the yellow LED will glow if there is insucient
oil. In this condition, the generator will not start. In this condition you need
to add oil for the generator to operate.
2. Load Status indicator (Fig E)
The red load status indicator light
(5) advises the operator that a fault
has been detected and the power
supply to the control panel has been
interrupted. When the red load status
indicator is operating red, there is NO
240Va.c. available to the control panel.
When the engine is running the load status indicator light (5) ashes under
the following conditions:
a. Flashing once indicates low voltage protection, caused by the engine
rotation speed not meeting the specied requirements.
b. Flashing twice indicates the engine is overheated, caused by high
temperature.
Preparation information Preparation Information
c. Flashing 3 times indicates overload protection caused by an excessive
electrical overload.
d. Flashing 4 times indicates there is an electrical problem most likely caused
by a short circuit.
In any of the above instances, when the red load status indicator light
(5) turns on, the power supply to the control panel will be disconnected
automatically.
NOTE:
The engine must be stopped and the issue resolved before the
power supply will be restored.
3. Power Supply indicator (Fig F)
The power supply indicator light (6) is
a green LED. It will only display green
when there is a 240V output available,
thus the generator must be operating.
This indicator will remain on when
the generator is operating and has
240Va.c. available to the control panel,
with or without appliances connected
to the AC sockets (9).
In an overload condition, there is no
240Va.c. available to the panel so the green indicator will not operate.
Preparing the Generator
It is important to check the generator before you commence operating
the unit.
IMPORTANT. Ensure that the engine has oil. When leaving the factory,
this generator has NO OIL in the engine.
NOTE. The engine will not start if the generator has no oil.
Checking the Engine Fuel
IMPORTANT: Fuel goes o after about 3-4 months. If you nd your generator
does not start, rst change the fuel in the tank with newly purchased fresh
unleaded fuel. Do not use ethanol based fuels.
IMPORTANT: If replacing old fuel from the generator ensure to drain the old
fuel from the carburettor bowl until the new fuel drains from the bowl. Drain
the bowl via the fuel drain (10).
D.
E.
Preparation Information
F.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone EP2800i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone EP2800i in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info