697434
36
Zoom out
Zoom in
Previous page
1/72
Next page
Operation
6720813171 (2016/05)36
Settings Menu
Step 1 [\/2/4| Display value. Currently measured CH flow temperature in °C. Also see section 14.2, page 53.
Step 2 Open the “Settings” menu? Yes: step 3
No: step 1
Step 3 To open the “Settings” menu: Press and hold the d + e buttons for more than 2 seconds
Step 4 [l/-/-] Display setting. As soon as the display shows [l/-/-], the “Settings” menu is open. You can set the boiler
performance using the first parameter shown on the display. Also see section 14.3, page 54.
Step 5 Adjust boiler performance? Yes: step 7
No: step 6
Step 6 Lower: Decrease the target boiler output with the c button. The minimum setting is [l/2/5] = 25 % with an 80-kW
boiler, [l/2/0] = 20 % with a 65 or 100-kW boiler and [l/3/0] = 30 % with a 50-kW boiler.
Higher: Increase the target boiler output with the d button. The maximum setting is [l/-/-] = 100 %.
This is equal to the factory setting.
Step 7 Press the e button.
Step 8 [f/\/5| Display setting: Set the second parameter as soon as the display shows [f/\/5|.
This parameter shows the target pump run-over time in minutes after heating operation has ended.
Also see section 14.3, page 54.
Note: Do not set a pump run-over time of less than [f/\/5| (= 5 minutes).
Step 9 Set the pump run-over time after heating operation has ended? Yes: step 10
No: step 11
Step 10 Lower: Decrease the target pump run-over time after the end of heating operation with the c button.
The minimum setting is [f/\/0| = 0 minutes. The factory default setting is 5 minutes.
Caution: Do not set the target pump run-over time after the end of heating operation to less than 5 minutes.
Higher: Increase the target pump run-over time after the end of heating operation with the d button.
The maximum setting is [f/6/0| = 60 minutes or [f/1/d| = 24 hours.
Step 11 Press the e button.
Step 12 [c/\/1| Display setting. Set the third parameter as soon as the display shows [c/\/1|. This parameter indicates
the DHW mode status setting. This enables DHW mode to be switched off or on. This setting has priority
over other DHW mode settings, such as those made on the room thermostat. Also see section 14.3,
page 54.
Step 13 Set the DHW mode status? Yes: step 14
No: step 15
Step 14 Set the DHW mode target status with the c or d buttons. [c/\/1| means “On”, [c/\/0| means “Off”.
Please note: Setting [c/\/0| also switches off the hot water cylinder frost protection.
Step 15 Have at least 5 seconds passed without a button being pressed and/or has the mains voltage been interrupted? Yes: step 17
No: step 16
Step 16 Press the e button.
Step 17 [\/2/4| Display value. Any adjustments that you have made have been confirmed. step 1
Table 13 Settings
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester-Bosch GB162-80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester-Bosch GB162-80 in the language / languages: English as an attachment in your email.

The manual is 5,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Worcester-Bosch GB162-80

Worcester-Bosch GB162-80 Installation Guide - English - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info