697434
35
Zoom out
Zoom in
Previous page
1/72
Next page
Operation
6720813171 (2016/05) 35
Step 14 [\/2/4| Display value. Currently measured CH flow temperature in °C. Also see section 14.3, page 54.
Step 15 Press the e button.
Step 16 [p/1.6| Display value. Currently measured system pressure in bar. Also see section 14.3, page 54.
Step 17 Press the e button.
Step 18 [-/h/\| Display code: Operating phase: The boiler is in service mode. Also see section 14.3, page 54.
Step 19 Press the e button.
Step 20 [\/2/4| Display value. Currently measured CH flow temperature in °C. Also see section 14.3, page 54.
Step 21 Have 30 minutes passed or has the mains voltage been interrupted? Yes: step 22
No: step 23
Step 22 Service mode is deactivated. step 25
Step 23 Deactivate service mode? Yes: step 24
No: step 15
Step 24 To deactivate the service mode: Press and hold the d button for more than 2 seconds until the dot disappears.
Step 25 The boiler capacity drops to the preset capacity, see the “Settings” menu (table 13). step 1
Manual operation menu
Step 1 [\/2/4| Display value. Currently measured CH (boiler) flow temperature in °C. Also see section 14.2, page 53.
Step 2 Activate manual operation? Yes: step 3
No: step 1
Step 3 To activate manual operation: Press and hold the d button for more than 5 seconds.
Step 4 [//2/4} Display code: Operating phase: As soon as a flashing dot is shown in the right-hand bottom corner of the
display, manual operation is active. This means that the boiler is permanently in heating mode. The
maximum CH flow temperature as set on the maximum CH flow temperature dial of the BC10 basic
controller (control panel) now applies. The “Heat request” LED lights up. DHW mode is possible during
manual operation.
Step 5 Press the e button.
Step 6 [p/1.6} Display value. Currently measured system pressure in bar. Also see section 14.2, page 53.
Step 7 Press the e button.
Step 8 [-/h//} Display code: Operating phase: Also see section 14.3, page 54. The boiler is in manual operation mode.
This means that the boiler is in heating mode while there is no heat request from the controller. During
manual operation the “Settings” menu (table 13 from step 3) can be used to temporarily change the
target boiler performance.
Note: If the boiler performance has been changed temporarily, this must be set again after ending
manual operation, according to the “Settings” menu (table 13, page 36).
Step 9 Press the e button.
Step 10 [//2/4} Display value. Currently measured CH flow temperature in °C. Also see section 14.2, page 53.
Step 11 Has there been a power failure? Yes: step 1
No: step 12
Step 12 Deactivate manual operation? Yes: step 13
No: step 5
Step 13 To deactivate manual operation: Press and hold the d button for more than 2 seconds until the dot disappears. step 1
Table 12 Manual operation
Service Mode menu
Table 11 Service mode
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester-Bosch GB162-80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester-Bosch GB162-80 in the language / languages: English as an attachment in your email.

The manual is 5,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Worcester-Bosch GB162-80

Worcester-Bosch GB162-80 Installation Guide - English - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info