638203

WOLF-Garten CSE 2240 Manual

31
Zoom out
Zoom in
Previous page
1/252
Next page
31
11.GENERAL SUGGESTIONS FOR
CUTTING
We recommend to cut by using the bottom of
the bar, a technique to pull the chain, so the
electric chainsaw tends to move towards the
trunk, decreasing the danger for the operator.
Be careful when cutting with the top of the bar,
because the electric chain saw would tend to
move towards the operator.
# Make sure to the cutting length.
# Avoid cutting of thin twigs and bushes.
The twigs can be grabbed by the chain, set in
rotation and cause injury.
# Pay particular attention to branches in
tension: they might be dangerous for the
operator.
# Be especially careful when working on slopes,
uneven and slippery ground.
# Do not cut wire mesh.
# Do not proceed with detailed jobs without first
having made the necessary experience.
In case of doubt and uncertainty, consult an
expert.
# It is recommended to cut logs upon tripods
or clamps to gain experience.
CUTTING LOGS
Cutting a log resting on the two
extremities
FIG. 12
# First cut 1/3 of a diameter from the top.
Next cut from below using the top of the bar.
This will avoid pinching of the bar in wood. Avoid
touching the ground with the bar.
Cutting from a saw horse
FIG. 13
# First cut 1/3 of a diameter from below.
Next cut from the top using the bottom of
the bar.
ENGLISH
FELLING A TREE
# Before felling a tree, consider carefully all
conditions including the intended direction of
the fall, the natural lean of the tree, surrounding
trees and obstacles, the wind direction and
speed.
Directional cut
FIG. 14
# Cut a wedge (1/3-1/2 of tree diameter) out
of the trunk on the side which you want the
tree to fall.
Felling cut
FIG. 15 - 16
# Cut into the trunk from the other side 1”- 2”/3-6
cm above the wedge.
# Use a felling wedge to help control felling
and prevent binding the guide bar and saw
chain in the cut.
# Safety distance is 2.5 times the height of the
tree to fell. Be sure that nobody is in the danger
zone before and during the felling.
CUTTING PREPARED TIMBER
# When cutting prepared, use clamps or shocks
to secure wood.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten CSE 2240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten CSE 2240 in the language / languages: All languages as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info