638203

WOLF-Garten CSE 2240 Manual

30
Zoom out
Zoom in
Previous page
1/252
Next page
30
8. SAFETY CHAINBRAKE
FIG. 2-9
# This area shows the part of chainsaw most
likely to cause kickback (fig. 9).
# In the event of kickback, the left hand will
come into contact With chain brake lever, that
incorporates a separate electrical switch to cut
out the current to the motor, stopping the chain
immediately (‘O’ position).
# To reset after operation of the chain brake,
disconnect from power supply and release
the brake by pulling the brake lever into the
rearward position (‘1’ position).
# Check chain tension before restarting.
9.SWITCHING ON/OFF
- SWITCH ON -
Hold the front handle with the left hand and the
rear handle with the right hand.
Press the lock off safety button (2) with the
thumb and press the start button (3).
- SWITCH OFF -
To stop the chainsaw, release the trigger.
ELECTRIC MOTOR SAFETY SYSTEM
This chainsaw has a device that protects the
motor by disconnecting it when the effort is too
high. To restart, release the trigger.
Check that the chain is able to rotate.
Push the trigger and the lock-off button to start
again.
10. MAINTENANCE
The following suggestions deal with the daily
maintenance of the chainsaw. If they could not
be exhaustive, contact an authorised service
centre.
FIG. 1 - 2 - 6 - 8 - 10
# Ensure that the electric power lead (9) is not
damaged.
# Ensure that the motor and air slots (8) are
free and unobstructed.
# Check that the lubrication system is
adequate.
# Clean the chain brake and ensure that it
works properly.
# Turn the bar over everyday.
# Check the bar wear.
# Ensure that the oil flow hole is
unobstructed.
# Clean the chain guide on the bar.
# Check the chain tension, sharpen the blades
and check their conditions eventually removing
irregularities.
# Check the guide bar sprocket conditions.
# Ensure that the oil reservoir and the oil filter
are clean.
This chainsaw meets all current legislation
requirements; in order to avoid injuries while
repairing, every repairing has to be done by
qualified staff in an authorized service centre.
CHAIN SHARPENING
FIG. 8
# Disconnect the cord from the mains supply.
# Wear protective gloves.
# Ensure the chain is correctly tensioned and
not too loose.
# Engage the chain brake (10) to block the
chain on the bar when sharpening.
# Use a round file for chain sharpening,
diameter equivalent to 1.1 times the cutting
tooth depth.
# File at a horizontal angle, 30° to the bar.
# File from inside towards outside of the tooth
only.
# Sharpen each tooth equally by using the same
number of strokes.
# File at an angle of 90° to the bar.
# Check the safety depth gauge height
every 5 chain sharpenings. Use depth gauge
measuring instrument to check the height of
the depth gauge.
ENGLISH
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten CSE 2240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten CSE 2240 in the language / languages: All languages as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info