638203

WOLF-Garten CSE 2240 Manual

29
Zoom out
Zoom in
Previous page
1/252
Next page
29
ENGLISH
engaged, and the brake lever is in position ‘1’.
# Unscrew the bar locking hand wheel (12) and
also remove the chain guard (11).
# Fit the bar (5) onto the locking pin
(13). Turn the adjustment flange in the direction
shown by the arrow of fig. 5, then push the bar
back all the way toward the pinion (14).
# Slide the chain (6) through the bar slot,
starting from the top section, making sure that
the teeth cutting edge is facing forward, on the
blade top side.
# Fit the chain around the pinion (14).
# Fit the chain guard and partly tighten the bar
locking hand wheel (12) by hand, as shown
in fig.6.
# Tension the chain by using the chain tension
adjustment hand wheel (12), fig. 7.
The tension is correct when the chain remains
inside the slot around the bar and can be turned
with the fingers. At this stage, fully tighten the
bar locking hand wheel, as shown in fig. 8.
# Too much tension on the chain will reduce the
life of the chain, the bar and the engine.
# Too little tension of the chain may cause
the chain to fall from the bar, and create a
dangerous condition for the user.
7. LUBRIFICATION SYSTEM
FIG. 10
# An automatic pump allows the chain
lubrication.
# Use only new oil for chains. The choice of the
oil viscosity depends on the air temperature.
Never use waste oil or second rate oil that could
damage the pump, the bar and the chain.
# Contact an authorised service centre in order
to choose good oil.
# Never use the chainsaw without oil. Check oil
level regularly, refill if less than ¼ full.
# If the lubrication system doesn’t work properly,
check that the oil filter is clean, eventually
contact an authorised service centre.
4. ELECTRICAL SAFETY
# Voltage: make sure your machine is correct
for your mains supply
# Current: your machine is suitable for AC
supply only.
# Plugs/extension leads: we recommend the
use of PVC or rubber covered plugs, connectors
and leads with your machine.
# Power point: the machine must be connected
to a power point and not a lighting
socket.
5. DESCRIPTION OF MACHINE PARTS
The package contains the following items:
1. Rear handle
2. Lock off safety button
3. Start lever
4. Chain oil tank
5. Bar with toothed pinion
6. Chain
7. Front handle
8. Air intakes
9. Power supply cable with plug
10. Brake-hand guard engaging lever
11. Chain guard
12. Bar locking hand wheel + chain tension
adjustment hand wheel
13. Bar locking pin
14. Chain pinion
15. Oil tank inspection gauge
16. Spiked bumper
17. Cable strain relief
NOTE: make sure that the power tool and
accessories in the package are not damaged
NOTE: read these operative instructions
carefully before attempting to operate the drill
6. BAR AND CHAIN ASSEMBLY
FIG. 1 - 2 - 3 - 4 -5 - 6
# Check that the chain brake (10) has not been
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten CSE 2240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten CSE 2240 in the language / languages: All languages as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info