813089
16
Zoom out
Zoom in
Previous page
1/83
Next page
Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 16 / 83
© wodtke GmbH Tübingen. All rights reserved. Subject to change without notice. Month of issue xx/2007 Art. No. 950 281
5.4 Preparations / Lighting the stove
Note: The ignition procedure starts anew every time the appliance is switched on as well as
after a power failure, and it can take up to 10 minutes before the first flame becomes visible
(depending on how clean the burner pot is).
Open the firedoor. Check whether the burner pot and firebox are free of soiling and pellets
and clean burner pot of pellets/ash/slag as necessary.
Close the door.
Open the combustion air pipe (if present).
Switch the stove on by pressing the I/O key (after delivery the display will generally show “G
OFF” or the “stand-by dot”). Now pellets are fed into the burner pot. The stove lights
automatically via the ignition cartridge installed in the device. The pellets will start
burning after 5-10 minutes at the latest.
If ignition fails (unburnt pellets in the burner pot), please first check whether the burner pot
is free of soiling (all air holes must be free; see also Chapter 0) and whether the fuel hopper
has been filled. If you are using the stove for the first time or the fuel hopper has run
completely empty it can take about 10 minutes before the pellets have passed the feed
screw. Clean the burner pot thoroughly before you try another start. Do not light the
pellets by hand . After a false start empty the burner pot completely and dispose of
the pellets and ash. Never return unburnt pellets from the burner pot to the fuel
hopper and never try to light them by hand.
Danger of fire through glowing embers and/or overheating!
Important information:
Do not restart the appliance immediately after a successful start. Instead let it cool
down for at least 5 minutes at “G OFF” before restarting. In this way you will avoid
overheating the appliance.
Be sure to keep the firedoor closed during the ignition phase and do not switch the
appliance on and off repeatedly.
5.5 Emergency operation with igniters
If the ignition cartridge of the appliance should fail you can still operate it when necessary by
using wodtke igniters. Light the pellets with the igniters as follows.
Open the firedoor. Check whether the burner pot and firebox are free of soiling and pellets
and clean burner pot of pellets/ash/slag as necessary.
Put wodtke igniters and a few pellets (never more than a handful) in the burner pot and
light them. Tip: Open the wodtke igniter a little before lighting it.
Close the firedoor and open the combustion air pipe (if present).
Switch the stove on by pressing the I/O key (after delivery the display will generally show “G
OFF” or the “stand-by dot”). Now pellets are automatically fed into the burner pot and the
flue gas fan starts running.
Caution:
Never use wood, paper, cardboard etc. or inflammable liquids for lighting the stove!
Never fill unburnt pellets or ash back into the fuel hopper.
Danger of fire through glowing embers!
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wodtke Frank SX waterplus S4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Frank SX waterplus S4 in the language / languages: German as an attachment in your email.

The manual is 3.18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke Frank SX waterplus S4

Wodtke Frank SX waterplus S4 User Manual - German - 76 pages

Wodtke Frank SX waterplus S4 User Manual - French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info