Manual Wmf Lumero - 12360011 (page 14 of 19) (English, German)

690821

Zoom out

Zoom in

1/19

26 27

Making espresso

1. Fill the water tank with drinking water using the amount of water you require, do not ﬁll beyond

the MAX marker.

2. Place a cup of the size you want under the outlet for the strainer. It is recommended that you

warm the cups before making coffee by rinsing them in hot water.

3. Insert the strainer for ground coffee (1 or 2-cup insert) into the strainer holder.

⋅ Before adding the ground coffee, make sure that the strainer is clean and there are no coffee

grounds from previous use.

⋅ Fill the strainer a little at a time to prevent spillages.

Note: Normally, for an espresso, use one level spoon of ground coffee (around 9 grams) from the

measuring spoon supplied, or weigh out around 14 grams for 2 cups. However, you can adjust the

amount to suit your taste. We recommend ﬁlling the strainer so it is heaped then clearing off the

excess coffee.

4. Distribute the ground coffee evenly and press down with the stopper. Pressing down the ground

coffee correctly is very important in order to make a good espresso. If it is pressed down too ﬁrmly,

the coffee runs through too slowly and is strong. However, if it is not pressed down enough, the

coffee runs through too quickly and is weak.

5. Remove excess coffee from the edge of the strainer and slot the strainer holder into the coffee

machine.

6. Use the handle to insert the strainer holder on the front left side of the device (8 o’clock position).

Engage the wide recesses on the strainer holder with the recesses on the brewer head. Turn the

handle as far as possible to the right to ensure the strainer holder engages properly.

7. Press the 1 or 2-cup button `->

to start the brewing process.

Note:

▪ During preparation, you can at any time press the same button again to stop the coffee pouring

out.

▪ To remove the strainer holder, twist the handle from right to left.

▪ Beware of burning! If no espresso comes out of the machine the sieves are probably blocked.

In this case please do not remove the portaﬁlter and wait for approximately one minute till the

pressure inside the machine has dropped.

Making espresso with coffee pods

The device is compatible with all common coffee pods.

Note: For larger coffee pods, we recommend using the 1-cup strainer holder. For espresso pods, use

the pod strainer holder.

1. Insert the strainer for coffee pods into the strainer holder.

2. Place the pad as centrally as possible in the strainer. Note the instructions on the packaging of the

coffee pod for the correct placement of the pod in the strainer.

3. In order to start making coffee, prepare the device by carrying out steps 1-3 under “Making

espresso” and press the 1 or 2 cup button ->

as required.

Beware of burning!

Allow the device to cool down! To avoid getting splashed with hot liquid, never remove the strainer

holder while the machine is making coffee! When it is ﬁnished, always wait a few seconds and then

release the ﬁlter holder.

Making cappuccino

Make espresso as described above using big enough cups.

4. Move the knob to the preheat steam symbol (G2) ->

, the light ring on the knob lights up red.

Wait for the machine to heat up. The control light on the knob then lights up continuously in

white.

5. Fill a mug just one third full with cold milk to make sure there is enough space for frothing the

milk.

Note:

▪ A tall, narrow mug is best as the whole milk frother should be in the milk without touching the

bottom of the mug. When choosing the size of the milk container, note that the milk volume will

increase by two to three times.

▪ The best milk to use is semi-skimmed at fridge temperature.

6. Twist the frother so that it is not above the collection bowl.

7. Hold the mug of milk directly below the frother so that the end of the foamer is just below the

surface of the milk.

8. Adjust the milk froth knob to (G1) ->

. Steam comes out of the milk frother.

9. Carefully move the mug up and down, making sure the end of the milk frother is in the milk at all

times. Do not take the milk frother out of the milk as it could splash.

10. Continue until you have all the froth you want.

11. Adjust the knob to

12. Spread the milk froth over the cup(s) of espresso.

Note:

▪ If you wish to make more than one cappuccino, ﬁrst make all the coffee, then make the milk froth.

▪ The steam output stops automatically after 60 seconds.

▪ Clean the milk frother and the steam nozzle immediately after use to ensure it does not get

clogged up with milk residue. See “Cleaning the milk frother”.

Cooling the device after frothing milk

Note: In order to avoid burnt coffee, allow the espresso machine to cool down after frothing milk.

Proceed as follows to speed up the cooling process:

1. Place a container under the milk frother:

2. Turn the knob to the output hot water symbol (G4) ->

and output hot water till hot water

stopped.

3. Turn the knob to

4. The device is now once again in standby mode.

Preparing hot water

1. The device is in standby mode.

2. Place a container under the milk frother.

3. Turn the knob to the right to output hot water (G4) ->

the hot water comes out of the milk

frother.

Note: The water output stops automatically after 60 seconds.

Sleep Mode

The device automatically switches to sleep mode after 30 minutes when it is in standby mode. The

1-cup button ->

lights up in red.

Why is the 1cup button of lumero WMF blinking color blue? What is the problem? Submitted on 30-1-2022 at 18:15
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wmf Lumero - 12360011 in the language / languages: English, German as an attachment in your email.

The manual is 8,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wmf Lumero - 12360011

Wmf Lumero - 12360011 User Manual - English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish - 83 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wmf Lumero - 12360011 Manual

Product: