Manual Wmf Lumero - 12360011 (page 13 of 19) (English, German)

690821

Zoom out

Zoom in

1/19

24 25

Display ﬂashes Hardness range Hardness

1 Soft 0 - 7° dH

2 Medium >7-14° dH

3 Hard >14–21° dH

4 Very hard >21° dH

To adjust the water hardness, follow steps 1-5 of “Activating the programme menu”. Then please

proceed as follows:

1. The programme menu is activated.

2. Brieﬂy press the 1-cup button ->

once

3. The 1-cup button ->

continues to light blue, while the 2-cup button -> ﬂashes white.

4. Press the 1-cup button ->

several times to adjust the water hardness level.

⋅ If you press the 1-cup button ->

once, the 2-cup button -> brieﬂy ﬂashes once

repeatedly. This changes the setting to Water hardness H1.

⋅ If you press the 1-cup button ->

again, the 2-cup button -> brieﬂy ﬂashes twice

repeatedly. This changes the setting to Water hardness H2.

⋅ If you press the 1-cup button ->

again, the 2-cup button -> brieﬂy ﬂashes three

times repeatedly. This changes the setting to Water hardness H3.

⋅ If you press the 1-cup button ->

again, the 2-cup button -> brieﬂy ﬂashes four

times repeatedly. This changes the setting to Water hardness H4.

5. If you have reached H4 and you press the 1-cup button again, the cycle restarts from the

beginning and the ﬂash sequence starts again with the signal for H1.

6. You can save the water hardness setting you want by brieﬂy pressing the 2-cup button ->

. The 1 and 2-cup buttons -> ﬂash red three times to indicate the setting has been saved

successfully.

NOTE: If you do not press any buttons in the water hardness programme for 15 seconds, the device

automatically exits the programme and starts the heating phase. By default, the device is set to the

highest water hardness level H4.

Setting the coffee temperature

To adjust the coffee temperature, follow steps 1-5 of “Activating the programme menu”. Then please

proceed as follows:

1. The programme menu is activated.

2. Brieﬂy press the 2-cup button ->

once

3. The 2-cup button ->

continues to light red, while the 1-cup button -> ﬂashes blue.

4. The 1-cup button ->

lights in the corresponding colour of the temperature setting:

Blue = low temperature

White = medium temperature

Red = high temperature

Note: The device’s default setting is “low temperature”.

5. Pressing the 2-cup button ->

switches between the three temperature settings. Starting with

low temperature, then medium and hot.

6. Brieﬂy press the 1-cup button ->

to save the setting. The 1 and 2-cup buttons -> ﬂash

red three times to indicate the setting has been saved successfully.

Please note: If you do not press any buttons in the temperature setting programme for 10 seconds,

the device automatically exits the program and starts the heating phase. In addition, the cups should

always be preheated for optimal temperature

Setting the volume per cup

The 1-cup volume for the device is set to a default of 30 ml. This volume can be adjusted individually.

In order to adjust the individual setting for 1 cup permanently, please proceed as follows:

1. Fill the water tank with drinking water using the amount of water you require, do not ﬁll beyond

the MAX marker. Fill the strainer with ground coffee.

2. Place a cup of the size you want under the outlet for the strainer.

3. Insert the strainer

4. The device is in standby mode. Press and hold the 1-cup button ->

for 3 seconds until the

brewing process starts. Release the button.

5. When the volume you want is reached, press the 1-cup button ->

again to save the amount.

Note: You can choose a volume between 15 ml and 65 ml.

6. The 1 and 2-cup buttons ->

ﬂash red three times to indicate the setting has been saved

successfully.

The 2-cup volume for the device is set to a default of 60 ml. This volume can be adjusted individually.

In order to adjust the individual setting for 1 cup permanently, please proceed as follows:

1. Fill the water tank with drinking water using the amount of water you require, do not ﬁll beyond

the MAX marker. Fill the strainer with ground coffee.

2. Place a cup of the size you want under the outlet for the strainer.

3. Insert the strainer

4. The device is in standby mode. Press and hold the 2-cup button ->

for 3 seconds until the

brewing process starts. Release the button.

5. When the volume you want is reached, press the 2-cup button ->

again to save the amount.

Note: You can choose a volume between 30 ml and 130 ml.

6. The 1 and 2-cup buttons ->

ﬂash red three times to indicate the setting has been saved

successfully.

To reset the individual setting and revert to the default setting for cup volume, the device needs to be

in standby mode. Then please proceed as follows:

1. Set the selector knob to the “Preheat steam” position (G2) ->

2. Press the 1 and 2-cup buttons

at the same time for at least 3 seconds.

3. The 1 and 2-cup buttons ﬂash red once. As an additional indicator that the setting has been saved,

the pump starts for 0.2 seconds.

4. The coffee volume is then reset to the default setting, 30 ml coffee for the 1-cup button and 60 ml

for the 2-cup button.

5. Reset the knob to

6. You can now reset the volume per cup again as described above or use the default setting.

Why is the 1cup button of lumero WMF blinking color blue? What is the problem? Submitted on 30-1-2022 at 18:15
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wmf Lumero - 12360011 in the language / languages: English, German as an attachment in your email.

The manual is 8,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wmf Lumero - 12360011

Wmf Lumero - 12360011 User Manual - English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish - 83 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wmf Lumero - 12360011 Manual

Product: