727497

Whynter ARC-122DHP Manual

10
Zoom out
Zoom in
Previous page
1/18
Next page
10
INSTALLATION
Location
The air conditioner should be placed on a hard and level surface strong enough to support its weight. The unit is
equipped with caster wheels for portability. It should only be rolled on smooth, flat surfaces. Use caution when
rolling on carpet surfaces. Do not attempt to roll the unit over objects.
The air inlet and outlet should be free of any obstructions and be placed with at least 20” of clearance for efficient
air-conditioning and circulation.
Exhaust hose Installation
When using the air conditioner, the hot air from the exhaust hose must be exhausted out of the room to complete
the air exchange of the condenser. The intake hose is optional. When the unit is operating in dehumidifying or fan-
only mode, installation of the exhaust hose is optional.
Window kit Installation
Your window kit has been designed to fit most standard vertical and horizontal windows. However, it may be
necessary for you to modify the installation procedures for your window.
NOTE:
If your window opening is smaller than the minimum length of the window slider kit, the window slider kit can be cut to
fit the window opening. Never cut into the exhaust and intake hose cut-outs on the window slider kit.
If your window opening is larger than the maximum length of the window slider kit, additional material will be needed
to cover the open space such as, Plexiglas, PVC plastic, ply wood, etc. Alternately, an additional window slider kit
can be purchased to be used in combination with the included kit.
When using the window slider kit on a window or sliding door, additional security measures may be needed.
1. Expand each end of the exhaust (large) and intake (small) hoses about 6”.
2. Install the Large Exhaust Slide Locking Hose Connector to one end of the
exhaust hose (large hose) and the Large Exhaust Hose Connector with tab cut-outs
to the other end of the exhaust hose (large hose) by turning counterclockwise.
3. Install the Small Intake Slide Locking Hose Connector to one end of the
intake hose (small hose) and the Small Intake Hose Connector with tab cut-outs to
the other end of the intake hose (small hose) by turning clockwise.
4. Slide each of the slide locking hose connectors onto the rear of the unit
(See illustration)
Only extend the hose to the necessary length, keeping it as short and as straight as possible. We do not recommend
extending the hose more than 9' long. If you are interested in purchasing an additional 5’ exhaust hose, please
contact support@whynter.com for retail sales information or visit whynter.com for a list of optional accessories.
Note: To remove the hose(s) from the unit, press the release button and slide the hose and connector out.
1. Open the window approximately 5”.
2. Adjust the length of the window slider to the same length and width of the opening of the window. Cut the window
slider if necessary to fit the length of your window.
3. Insert the fixture through the back grooved side of the window slider hose cut-out. Line up the fixture with the 4
screw holes and tighten the fixture with 4 screws from the front side of the slider panel. (Fig. 1)
4. Fit the window slider kit into the window opening and close the window to secure the window slider kit. For long
term installation, you may screw the window kit into your window frame.
5. Move the air conditioner close to the window, extend the hoses to the necessary length, keeping them as short
and as straight as possible and attach the other end of each hose to the window slider kit.
6. Align the tab cut-outs of the hose connectors to the tabs on the fixtures and snap the hose connectors to the
window slider kit.
Fig. 1
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whynter ARC-122DHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whynter ARC-122DHP in the language / languages: English as an attachment in your email.

The manual is 6,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info