For the electrical connection, use an H05RR-F cable as specified in the table below.
Connect the yellow/green earth wire to the terminal with the symbol .
This wire must be longer than the other wires.
1.Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B).
2.Insert the power cable in the cable clamp and connect the wires to the terminal block as indicated in the connection diagram located near it.
3.Secure the power cable with the cable clamp.
4.Close the cover (C) and screw it on the terminal block with the removed screw - point (1).
Each time the power is connected, the hob performs an automatic check for a few seconds.
If the hob already has a power cable, follow the instructions attached to the cable. Connect the appliance to the power supply by means of a multipole switch with minimum
contact gap of 3mm.
NOTE: When using the hob for the first time, please take care not to have powerful halogen lights, like those of a hood, shining over the sensor button area of the hob. These
lights may interfere with the starting of the system.
Control Panel Description
The panel has touch controls: to use them, just press the corresponding symbol (a light touch is sufficient).
ELECTRICAL CONNECTION
WARNING
-Disconnect the appliance from the power supply.
-Installation must be carried out by qualified personnel who know the current safety and installation
regulations.
-The manufacturer declines any liability for injury to persons and animals or damage in case of failure to comply with the instructions provided in this
section.
-The power cable must be long enough to allow the hob to be removed from the worktop.
-Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home.
-Do not use extension cords.
WiresNumber x size
230 V ~ +
3 x 4 mm2
230-240 V ~ +
3 X 4 mm2 (Australia only)
230 V 3 ~ +
4 x 1.5 mm2
400 V 3N ~ +
5 x 1.5 mm2
400 V 2N ~ +
4 x 1.5 mm2
INSTRUCTIONS FOR USE
400 V 3N ~230 V ~
230-240 V ~ (Australia only)
230 V ~ (UK only)
400 V 2N ~230 V 3 ~ (Belgium only)400 V 2N ~ (NL only)
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool ACM 723 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool ACM 723 in the language / languages: English, Dutch, French, Italian as an attachment in your email.
The manual is 12,25 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
