686265

Weldkar MIG 2125 INVERTER WELDER Manual

19
Zoom out
Zoom in
Previous page
1/44
Next page
19
4. MAINTENANCE
ANY MAINTENANCE OPERATION MUST BE
CARRIED OUT BY QUALIFIED PERSONNEL.
4.1 MAINTENANCE OF THE
WELDING INVERTER
In the case of maintenance inside the machine, make
sure that the switch (3) is in position “0” and that
the power cord is disconnected from the mains. It is
also necessary to periodically clean the interior of
the machine from the accumulated metal dust, using
compressed air.
4.2 PRECAUTIONS AFTER REPAIRS
After making repairs, take care to organize the wiring
so that there is secure insulation between the primary
and secondary sides of the machine. Do not allow the
wires to come into contact with moving parts or those
that heat up during operation. Reassemble all clamps
as they were on the original machine, to prevent a
connection from occurring between the primary and
secondary circuits should a wire accidentally break or
be disconnected. Also mount the screws with geared
washers as on the original machine.
FAULT CAUSE
Feed roller driven by motor in the
cabinet slipped.
Wire spool brake is too tight.
Wire spool unwinded and tangled. Wire spool brake is too loose.
Worn or incorrect feed roller size. Use a feed roller matched to the size you are welding.
Replace feed roller if worn.
Wire rubbed against the mis-aligned
guides and reduced wire feedability.
Mis-alignment of inlet/outlet guides.
Liner blocked with swarf. Increased amounts of swarf are produced by the wire passing through the feed
roller when excessive pressure is applied to the pressure roller adjuster.
Swarf can also be produced by the wire passing through an incorrect feed
roller groove shape or size.
Swarf is fed into the conduit liner where it accumulates thus reducing wire
feedability.
Incorrect or worn contact tip The contact tip transfers the weld current tot he electrode wire. If the hole
in the contact tip is too large then arcing may occur inside the contact tip
resulting in the wire jamming in the contact tip.
When using soft wire such as aluminium it may become jammed in the contact
tip due to expansion of the wire when heated.
Poor work lead contact to work piece. If the work lead has a poor electrical contact to the work piece then the
connection point will heat up and result in a reduction of power at the arc.
Bent liner. This will cause friction between the wire and the liner thus reducing wire
feedability.
4.3 TROUBLESHOOTING & SERVICE
Problems with inconsistent wire feed:
Wire feeding problems can be reduced by checking the following points:
eng
deufra ned
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Weldkar MIG 2125 INVERTER WELDER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Weldkar MIG 2125 INVERTER WELDER in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info