686265

Weldkar MIG 2125 INVERTER WELDER Manual

17
Zoom out
Zoom in
Previous page
1/44
Next page
17
3. INSTALLATION
This must be carried out by skilled personnel. All
connections must be carried out according to current
regulations, and in full observance of safety laws (CEI
reglement 26-10 – CENELEC HD 427).
- Make sure that the supply voltage matches the
voltage indicated on the specifications plate.
- When mounting a plug, make sure it has an
adequete capacity, and that the yellow/green
conductor of the power supply cable is connected to
the earth pin.
WARNING! Extension cords of up to 30 m must have a
crosssection of at least 2.5 mm².
3.1 DESCRIPTION OF THE EQUIPMENT
1) MIG Welding Torch Adapter (Euro connector).
2) Earth cable output terminal (-)
3) Power switch: control power through and break
4) Shielding Gas Inlet.
5) Power Access client: access to cable
6) Fan: for cooling the machine.
7) Digital display (Voltage).
8) Power indicator: Indicates that the machine is
turned on.
9) The indicator will illuminate if the duty cycle of the
power source has been exceeded.
10) Digital display (Welding current, Wire speed).
11) Indicates that the display (10) shows the MIG
welding wire speed.
12) Indicates that the display (10) shows the welding
current.
13) 2T or 4T mode selection Button.
14) Wave control: Is used to adjust the intensity of the
welding arc.
15) Setting knob: In relation to the selected LED,
regulates: the welding current
(LED 12) or wire speed in MIG welding (LED 11).
16) Setting knob: regulates welding voltage.
3.2 REEL FITTING SEQUENCE
1. Mount the wire reel.
2. The wire reel hub incorporates a friction brake which
is adjusted during manufacture for optimum breaking.
If it is considered necessary, adjustment can be made
by turning the large nut inside the open end of the
hub clockwise to tighten the brake.
3. Use the nut to secure the wire reel.
3.3 WIRE FEED
Make sure that the groove of the rollers matches the
wire diameter used. Mount the wire coil and slip the wire
into the feeder and torch sheath. Remove the gas nozzle
and unscrew the contact tip (located on the end of the
torch). Turn on the machine. Press the torch trigger until
the wire protrudes. Tighten the contact tip and replace
the gas nozzle.
3.4 GAS CONNECTION
- Secure the welding grade shielding gas cylinder
in an upright position by chaining it to a suitable
stationary support to prevent falling or tipping.
- Connect the regulator inlet connection to
cylinder or pipeline and tighten it firmly but not
excessively, with a suitable spanner.
- Connect and tighten the outlet hose firmly.
- Open the reducer of the cylinder and adjust the
gas flow to 8 – 10 l/min.
CAUTION: Make sure the gas used is compatible
with the material to be welded.
4
3
1
2
6
5
Figure 1
Figure 3
Gas cylinder
Pressure reducer
Shielding
gas
Welding torch
Power source with
wire feed unit
Earth clamp
Workpiece
7
9
8 10
11
12
13
141516
Figure 2
eng
deufra ned
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Weldkar MIG 2125 INVERTER WELDER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Weldkar MIG 2125 INVERTER WELDER in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info