Manual Webasto Pure II (page 18 of 379) (All languages)

802209

Zoom out

Zoom in

1/379

6 5110757E OI II Webasto Pure

NOTE

In some countries, single-phase charging is limited to

a defined current. The local connection requirements

must be observed.

All protective devices specified below must be designed

such that the charging station is disconnected from the

grid in the case of a fault. You must meet national install-

ation regulations and standards when selecting the pro-

tective device.

8.2.1 Dimensioning of the Residual Current

Circuit Breaker (RCCB)

The national installation regulations generally apply. Un-

less otherwise specified therein, each charging station

must be protected by an appropriate residual current

device (RCD type A) with a trip current of ≤30mA.

8.2.2 Dimensioning of the circuit breaker

The circuit breaker must conform to IEC 60898. The let-

through energy (I²t) must not exceed a maximum 80,000

A²s.

Alternatively, a residual current circuit breaker combina-

tion (RCBO) according to EN 61009-1 can be used. The

aforementioned parameters apply for this circuit breaker

combination.

8.2.3 Mains isolation device

The charging station does not have its own main ON/OFF

switch. The protective devices installed in the power sup-

ply system are therefore also used to disconnect the

power supply.

8.3 Installation

See also chapter15, "Assembly" on page 9. The sup-

plied installation material is intended for mounting the

charging station on a concrete wall or on an external

stand. For installation on a stand, the mounting material

is included in the scope of delivery of the stand.

üScope of delivery is checked for completeness.

uTake into account the mounting position at the install-

ation location. See Fig. 14.

NOTE

The central hole must be drilled!

uRemove the drill template at the perforation from the

packaging.

uMark the four positions of the drill holes at the install-

ation location using the drill template. See Fig. 14.

uDrill 4 holes of Ø 8mm in the marked positions.

uPosition the bracket over the upper holes and mount

using 2 wall plugs and 2 screws, 6x70mm, T25.

uRemove the lower cover from the connection area of

the charging station.

Fig.8

uRemove the spiral antikink protection from the con-

nection area of the charging station and place it with

the other supplied material.

uFor surface mounting, make a recess for routing the

lead on the back of the charging station using the des-

ignated lateral predeterminedbreakingpoints (if ne-

cessary deburr the edge of the break using a round

file).

uInsert the lead through the designated lead-through

and fit the charging station on the previously mounted

bracket.

uMount the charging station using 2 screws,

6x90mm, T25 using the mounting holes in the lower

connection area. Do not exceed the max. torque of

6Nm.

8.3.1 Connecting the charging cable

uPush the spiral antikink protection with the threadless

opening forward over the supplied charging cable.

uGuide the charging cables through the previously pre-

assembled sealing clip.

NOTE

Ensure correct fit of the previously pre-assembled rub-

ber seals in the sealing clip.

uPush the charging cable at least 10mm beyond the

upper edge of the clamping area of the strain relief

clamp.

uTurn the antikink protection spiral several turns onto

the sealing clip.

NOTE

Do not tighten yet.

Fig.9

uScrew in the supplied strain relief clamp in the correct

position on the charging cable.

NOTE

The strain relief clamp has two position options for

charging cable versions 11kW and 22kW.

Ensure that the “11 kW installed” label for an 11 kW

charging cable is visible.

uFit the strain relief clamp in the correct mounting posi-

tion using the supplied self-tapping Torx screws

(6.5x25mm) and tighten to 5.5Nm. (Attention: Do

not overtighten screws).

uThe strain relief clamp must be flush when securely

screwed in.

NOTE

Perform a tension test on the charging cable to make

sure that the cable cannot move.

uScrew the antikink protection spiral onto the sealing

clip with a torque of 4Nm.

uUsing the slot-head screwdriver (3.5 mm), connect the

individual cable ends according to the specification in

the illustration on the right terminal block with the

"out" label.

uTo do this, insert the screwdriver in the designated up-

per opening of the spring relief for the terminal block

and open the clamping spring.

uNow insert the individual wire into the designated

connection opening of the terminal block (lower open-

ing).

Charging cable Description

Blue N

Brown L1

Black L2

Grey L3

Yellow-green PE

Black-white Control cable (CP)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Webasto Pure II in the language / languages: All languages as an attachment in your email.

The manual is 28.17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Webasto Pure II Manual

Product: