805501

Watts WFHC-MASTER H and C-RF 6 ZONES Manual

8
Zoom out
Zoom in
Previous page
1/52
Next page
8
7. RF INITIALIZATION
Standard thermostat initialization: WFHT-BASIC-RF or WFHT-LCD-RF
First of all to enter in the parameters menu, go to the Comfort mode, press once and maintain
the (Ok) key then press on the same time on the (◄) key. The first parameter must be appears
“F0 ProG”, you can now release the keys.
By pressing several times on the (►) key, go to the “rF init” parameters, then press again on
the (OK) key to enter in the “rf init” mode. The following display (Fig.a) must appear:
Fig.a Fig.b Fig.c
Graphic scope description:
2 squares (Fig.b) = reception of correct RF init signal from a thermostat.
1 square (Fig.c) = reception of standard signal from a thermostat.
nothing = the receiver did not detect any radio signal
1. Use (◄) & (►) to change the zone number and move the green blinking LED cursor on
the master/slave DISPLAY.
Use (Ok) to select or de-select this zone and move to the next zone. (The zones selected stay
light up in green)
2. When you have correctly selected the zones to be assigned to an RF Thermostat go to the
RF Thermostat and activate its RF Initialization (see RF Thermostat user manual).
3. The green LED of the zone previously selected should now extinct; two squares scrolls on
the graphic scope indicate also a correct RF initialization.
4. When the RF Thermostat has been correctly assigned to the selected zones, on the
thermostat you can exit the RF Init mode. (don’t forget to switch off the thermostat to avoid
perturbation if you need to assign other thermostats)
5. You can repeat the step 1 to 4 to assign other RF thermostats to the other zones.
6. To exit the “RF init” mode and save this configuration, press (Ok) during 5 sec to return to
the main menu.
You can now perform radio range verification:
Place the RF Thermostat in the room where you need to regulate the temperature, adjust the
setting temperature on the maximum position (5).Close the doors and come back to the WFHC-
MASTERH&C-RF 6 ZONES. Verify that the LED of the concerned zone shines in RED (the
installation must be in heating mode), to be sure repeat these step another time (position 1,
LED = OFF, Position 5 LED = RED).
If the WFHC-MASTERH&C-RF 6 ZONES doesn’t receive correctly the orders of the thermostat,
check the RF installation, antenna position...
You could also check the graphic scope on the RF init mode to be sure that the signal is
received correctly (Fig.c).
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Watts WFHC-MASTER H and C-RF 6 ZONES at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Watts WFHC-MASTER H and C-RF 6 ZONES in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info