Manual Wanders Balsa 100 (page 20 of 64) (English, German, Dutch, French)

571834

Zoom out

Zoom in

1/64

failed. Possible cause: air in the pilot burner pipe.

Important: If the pilot ame has gone out you must wait at least 5 MINUTES before repeating the

above-mentioned steps.

Setting the height of the ames

• After igniting the burner, the height of the ames will automatically reach the maximum position.

• Press button  continuously to lower the ames and to switch o the burner (putting the re out: “STAND

BY”). Press button  briey to gradually lower the ames.

• Press button  to increase the ame height. Briey press button  to gradually increase the ames.

Switching o the appliance

• Press button  to lower the ames and to switch o the burner.

• Then press “OFF” button  to switch o the entire unit, including the pilot ame.

• If the appliance is not used for a longer period it is advisable that you turn o the gas valve in the gas pipe.

Important: if the pilot ame has gone out for whatever reason, you must wait at least 5 MINUTES

before lighting the pilot ame again.

Failure

If it looks as if the signals of the remote control are not properly received by the stove (receiver), it may be

caused by:

• Empty batteries: change the batteries.

• An electronic problem: solve it by pressing the “RESET” button on the receiver.

• If the appliance often switches o you should contact your installer.

Control (manual control)

If the batteries are due for replacement or if the receiver is defect, you can also operate the hearth by hand.

To do so, you need to disconnect the ignition (piezo) cable of the receiver and slide it gently onto the piezo

connection of the gas control block.

Lighting the re and putting it out

1. Open the gas stopcock which is mounted in the gas pipe leading to

the appliance.

2. Press “O I” switch  on the gas control block in the “I” position.

3. Turn motor switch  on the gas control block all the way to the right.

The switch will make a ticking sound.

4. Turn operating switch  on the gas control block in the MAN

position; an orice  becomes visible.

5. Push the metal pin in the orice with something like a small pen. The

gas will now ow to the pilot.

6. While keeping the metal pin pressed in, press the (square) ignition

fuse  (next to the “O I” switch) to ignite the pilot ame. Look through

the glass to see whether the pilot ame is burning.

7. If the pilot ame is burning, keep the metal pin pressed for another

10 seconds and then release it. If the pilot ame dies, wait for another

5 minutes before repeating the above steps.

8. Turn operation knob  to the “ON” position.

9. Turn motor switch  to the left to ignite the burner and to select the

height of the ames.











Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wanders Balsa 100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wanders Balsa 100 Manual

Product: