Manual Wanders Balsa 100 (page 19 of 64) (English, German, Dutch, French)

571834

Zoom out

Zoom in

1/64

Setting the time

• Press the big-ame button  and the small-ame button  simultaneously, and the display will show short

ashes to indicate that you are in the set mode.

• When in the set mode, press the big-ame button  to set the hours, and press the small-ame button 

to set the minutes.

• Wait or press the OFF button  to return to manual control.

Switching from ºC/24-hour to ºF/12-hour indication

• Press the OFF button  and the small ame button  simultaneously (2 sec) to switch from ºF (and the 12-

hour indication) to the ºC (and the 24-hour indication), and vice versa.

Possible settings

• By pressing the SET button  you can switch quickly between MAN  day temperature  lamp  ventilator

 night temperature  timer  MAN.

• MAN: this setting allows you to turn the ames manually higher or lower with the big-ame button  or the

small-ame button .

• Day temperature (): this mode allows you to set the desired daytime temperature; the remote control set

will function as a thermostat.

• Night temperature (): this mode allows you to set the desired night temperature.

• TIMER: this mode allows you to preset 2 switch-on and 2 switch-o times per 24 hours. If the night setting is

on - - -, the stove will burn on the pilot ame.

Setting the temperature

• Select the day temperature or night temperature by briey pressing SET button .

• Now press SET button  longer until the display starts ashing.

• Preset the temperature with buttons  or  (5 ºC is the minimum day temperature).

• Wait or press OFF button  to switch back to the thermostat-controlled system.

• In order to save the batteries you are advised to reset the night-temperature until the display shows the ‘- - -‘

signal.

Setting the timer function

• Select the timer function by briey pressing SET button  a few times.

• Now press the SET button  longer until P1 () starts ashing.

• Set the hours with button  and the minutes with button .

• Briey press SET button  for the next timing.

• Once all 4 timings have been set, press OFF button  to end the presetting.

Operation (remote control)

Igniting the re

• Open the gas turncock that is xed in the gas pipe leading to the stove.

• Press “O I” switch  on the gas control block in the “I” position.

• Turn control button  on the gas control block to the ON position.

• Simultaneously press buttons  and  on the handset. A short acoustic

signal indicates the start, and is followed by short acoustic signals (0.2

sec/signal, 1Hz.) until the pilot ame and the chief burner are ignited.

After the main burner has lit, the ame height will automatically go to

the maximum position.

Possible error messages

• Long signals (0.8 sec. signal with 0.2 sec. interval) during lighting : batteries of the receiver are almost

empty. (After hearing this signal, you can switch on the appliance for about another 10 times.)

• 5 seconds continuous signal : error message. One of the cables may not be connected, or the “O I” switch

is not in the “I” position.

• 5 short signals (0.2 sec. signal with 0.2 sec. interval) : ignition of the pilot ame and the main burner has





Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wanders Balsa 100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wanders Balsa 100 Manual

Product: