813271

Wamsler K158 Manual

47
Zoom out
Zoom in
Previous page
1/120
Next page
47
3. INSTALLATION
3.1 Installing the top lid
The top lid hinge spigots are inserted evenly into the plug holes in the stove frame (at back,
left and right) (Fig. 23 & 24).
3.2 Flue gas connector direction
The pipe connector is factory installed at the back of the stove.
If a flue gas connection is required on the side, left or right, the following steps should be
taken:
- Remove the pipe connector at the back by undoing the three fixing bolts M4 (Fig. 25).
- Close the smoke hole with the pair of cover plates supplied (Fig. 26).
- The smoke hole cover on the side wall and the inside cover should be removed. The
inside cover can be removed by taking the hotplate off and holding the cover screw
out the bolt (Fig. 27)
- cut out the aluminium insulation with a knife (Fig. 23).
- Screw the previously removed pipe connector from the back of the stove on to the side
using the three bolt holes (Fig. 28)
- If the flue gas connection is to go up, then proceed as follows:
- remove the pipe connector and close the back smoke hole.
- Take the smoke hole cover from the hotplate (the best way is to lift the plate) and
attach the pipe connector firmly using the three visible bolt holes (Fig. 29 & 30).
- Keep the remaining covers in a safe place for possible use later.
3.3 Installation of the heat exchanger and the heat sink
The heat exchanger and the heat sink are not part of the standard scope of supply of the
central heating stove. If required it can be retrofitted. The following is required:
- Insert the heat sink probe in the fully into the immersion shell (Fig. 31).
- Clamp the protective tube firmly in the immersion shell (Fig. 32).
- To install the heat exchanger only the blind flange on the back of the stove needs to
be removed and the heat exchanger connected in its place (Fig. 33).
ATTENTION
The heat exchanger has to be firmly bolted to the heating pocket (Fig 34).
Screw thread bolts can strip if too much force is used.
3.4 Installing the stove bar
Two screws underneath the front on the stove frame are already installed for attaching the
stove bar (Fig. 35).
- open fire door
- unscrew screws
- lay one end of the bar on the fire door
- first screw the bar on at the other end
- for easier access to the screws, the two front covers on the left and right of the fire
door can be removed.
- there is a screw at the bottom of each of the covers which must be undone. (Fig. 36)
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wamsler K158 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wamsler K158 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info