649002

Wagner Super Finish 31 Manual

11
Zoom out
Zoom in
Previous page
1/30
Next page
Super Finish 27 • 31
33
GB
Cleaning unit from outside
Achtung

spray gun is alternately opened and closed.
Achtung
In case of coating materials diluted with



Fill upper hopper with suitable cleaning agent.1.
Switch on unit, set multifunction switch to
2.
(ON -
circulation).
Operate unit for a few minutes in circuit with spray gun
3.
closed (without tip).
Set multifunction switch to 4. (spray).
Pull trigger guard on spray gun.5.
Pump cleaning agent into a separate, open container until 6.
the unit is empty.
Attention
In the case of coating materials containing sol-
vents, the container must be earthed.
Danger


See safety regulations.
Switch o unit, set multifunction switch to 7.
(OFF).

Danger
First of all pull out mains plug from socket.
4.

Leave the suction system submerged in the coating
material or submerge it into the appropriate cleaning agent.
Suction lter and unit should not dry out.
Attention
In using quick-drying - or two-component
coating material, do not fail to rinse unit
through with a suitable cleaning agent during
the processing period.
8. 

Cleanliness is the surest guarantee for disturbance-free opera-
tion. Always clean the unit after completing spraying work. In
no event may residue of the coating material dry and collect
in the unit. The cleaning agent used for cleaning (only with
a ash point of over 21 °C) must correspond to the coating
material.


see operating manual for spray gun.
Dismount tip and clean, see page 45, point 13.2.


Remove suction system from the material vessel, e.g. put
1.
unit in the horizontal set-up position.
Switch on unit, set multifunction switch to
2.
(ON–
circulation) and further to (spray).
Pull the trigger guard on the spray gun in order to pump
3.
residue coating material from the suction pipe, the high-
pressure hose and the spray gun into an open container.
Attention
In case of coating material containing solvents,
the vessel must be earthed.
Danger


regulations.
Submerge suction system in a suitable cleaning agent.4.
Set multifunction switch to 5.
(OFF).
Screw on spray gun on suction pipe (g. 12) with the two 6.
accompanying spanners 22 mm.
Set multifunction switch to 7. (ON – circulation).
Pump suitable cleaning agent in the circuit for approx.
8.
1 minute.
Pull trigger guard on spray gun and hold with clamp.9.
Set multifunction switch to 10. (spray).
Clean suction pipe for about three minutes.11.
Rinse in circuit – set multifunction switch to 12. (ON).
Close spray gun.13.
When cleaning with water, repeat procedure for about three
14.
minutes with clear water.
Switch o unit – set multifunction switch to 15. (OFF).
Cleaning unit (shutting down operation)
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wagner Super Finish 31 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wagner Super Finish 31 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 5,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info