517983
39
Zoom out
Zoom in
Previous page
1/122
Next page
GB
39
3.0 GENERAL SAFETY AND INSTALLATION INSTRUCTIONS
Warning! Due to risk of short circuits, always disconnect the
negative pole of the battery before starting work.
In the case of vehicles with a supplementary battery, also
disconnect this negative pole.
Warning! Improper cable connections may result in short circuits
which can cause:
- cable fires
- triggering of the airbag
- damage to electronic control equipment
- failure of electrical functions
(blinkers, brake lights, horn, ignition, lights).
Please note the following:
For working on the cables, the following terminal designations are used:
30 (input from battery plus direct)
15 (switched plus, behind battery)
31 (return cable from battery, neutral)
Use only insulated cable brackets, connector plugs and tabs. Do not use
crimp connections (cable connectors) or lustre terminals. The securest form
of connection is by soldering the cable ends and then insulating the
connection.
For connecting the cables use crimping pliers
For cable connections to 31 (earth):
Attach the cable with a bracket and toothed washer to an earthing screw
on the vehicle or screw it onto the metalwork of the vehicle using a
bracket, metal screw and toothed washer.
Always ensure a good earthing connection!
Caution! When disconnecting the negative pole of the battery, all
the volatile memories of the convenience electronics lose their
stored data.
206
Mulighet 1 (se
C 2):
Montering på den eksisterende, eller en ekstra montert (B 6) gasstag.
Bowden-kabelen til MS 50 festes ved hjelp av den dreibare bolten. Hvis
gasspedalen bejenes manuelt, glir Bowden-kabelen til MS 50 gjennom
bolten.
Mulighet 2 (se
C 3):
Montering på en eksisterende Bowden-kabel. Bowden-kabelen til MS 50
festes ved hjelp av klemblokken som er forbundet med gass-wiren. Hvis
gasspedalen bejenes manuelt, glir Bowden-kabelen til MS 50 gjennom
klemblokken.
BOWDEN-KABELFESTE
Se D 1 til E 1.
MONTERING I KJØRETØY UTEN GASS-WIRE
Se E 2.
VAKUUMSERVOENHET - VAKUUMTILSLUTNING (SE
E 3)
Vakuumslangen skal alltid skjæres over mellom tilbakeslagsventil og
innsugningsmanifold eller vakuumpumpe (på motorsiden)
1. Skjær vakuumslangen over mellom tilbakeslagsventil og
innsugningsmanifold eller vakuumpumpe (på motorsiden).
2. Sett inn et passende T-sykke (B 44, B 45, B 48) mellom de avskårne
vakuumslangene, og sikre dem med slangeklemmer.
3. Koble sammen vakuumservoenheten og tilkoblingene til T-stykkene med
vakuumslangen (B 47).
INSTALLASJON AV VAKUMSERVOMEKANISMEN, MONTERINGSMULIGHETER
Book_MS-50_A6.p65 10-02-2003, 11:1139
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Waeco MagicSpeed MS50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Waeco MagicSpeed MS50 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info