540482

Vortex RAZOR HD GEN II Riflescope Manual

7
Zoom out
Zoom in
Previous page
1/11
Next page
13 12
RETICL E
riflescope mounTing
To get the best performance from your Vortex Razor HD riflescope,
proper mounting is essential. Although not difficult, the correct steps
must be followed. If you are unsure of your abilities, it would be best to
use the services of a qualified gunsmith.
Rings and Bases
Mount an appropriate base and matching rings to your rifle according
to the manufacturer’s instructions. The Vortex Razor HD riflescopes
require 34 mm rings.
Vortex Optics highly recommends using the Vortex Precision Matched
34 mm ring sets which may be purchased from an authorized Vortex
riflescope dealer. These rings will mount to any Picatinny spec base.
If using an aftermarket base and ring setup, use the lowest ring height
that will provide complete clearance of scope and rifle—avoiding any
contact with barrel, receiver, bolt handle or any other part of the rifle.
A low mounting will help assure proper cheek weld, aid in establishing a
solid shooting position, and promote fast target acquisition.
Steps for Bore Sighting and Range Sighting
Be sure the L-TEC turret caps are correctly positioned with the 0 mark
on the turret cap indexed to the reference line on the turret body (see
page 11).
1. Loosen the turret top cover with a coin or
screwdriver to reveal the circular scale on the top
of the turret.
2. Use the wrench to loosen
three set screws located on cap
perimeters.
3. When adjusting, use the reference line and
circular scale (MOA or MRAD) in the center
of the turret housing to measure the desired
adjustments.
4. Using a screwdriver, turn the brass center
screw to make the adjustments changing the
bullet’s point-of-impact. No clicks will be felt
when making this adjustment.
5. Once desired zero has been achieved, re-tighten three set screws.
For best performance, turn in each of the three set screws until lightly
seated. Then, go back and continue to turn each screw a little bit at a
time until all three are fully tightened down.
6. Replace the turret top cover.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vortex RAZOR HD GEN II Riflescope at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vortex RAZOR HD GEN II Riflescope in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info