764122

Vonroc VC502AC Manual

9
Zoom out
Zoom in
Previous page
1/48
Next page
EN
9
WWW.VONROC.COM
(21) is covered as shown in Fig. C-2.
5. Reattach the top section (10) again and lock
the locking clamp (6).
6. Insert one end of the hose (11) into the vacu-
uming port (3). Fully unwind the suction hose
(11).
7. Connect the mains plug.
8. Press the power switch (1) into the “ ON/1”
position to start your vacuum cleaner.
9. The machine now is ready for wet vacuum
cleaning.
10. Press the power switch (1) into the “ OFF/0”
position to switch off your vacuum cleaner.
11. Raise the hose (11) so that the liquids drains
into the container (9).
12. Empty the container (9) immediately after suc-
tion cleaning because it is not designed to store
liquids.
Blow function (Fig. A, E - F)
Operation without the use of a filter is
recommended.
Remove all dirt and debris from the
container (9) before you use the blow
function.
Always wear safety goggles before using
the blowing function.
Risk of flying objects. Keep bystanders
away from the work area.
Your vacuum cleaner is equipped with a blowing
function. It can be used to blow dust and debris out
of garages or off patios and driveways.
1. Switch off (1) the machine and remove the
mains plug from the mains.
2. Unlock the locking clamp (6) and remove the
top section (10).
3. Before blowing, remove the dust collection bag
(16), the filter (17, 18) and remove all dirt and
debris from the container (9).
4. Reattach the top section (10) again and lock
the locking clamp (6).
5. Insert one end of the hose (11) into the blowing
port (4) on rear of machine. Fully unwind the
suction hose (11).
6. Connect the mains plug.
7. Press the power switch (1) into the “ ON/1”
position to start your vacuum cleaner.
8. The machine is now ready for blowing dust and
debris.
9. Press the power switch (1) into the “ OFF/0”
position to switch off your vacuum cleaner.
Finish operation (Fig. A)
1. Turn off (1) the machine and disconnect the
mains plug.
2. Remove the top section (10) and empty the
container (9).
3. Clean the machine with a soft cloth.
4. Stow away the mains cable and accessory at
the machine. Store the appliance in a dry room.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and dirt.
Remove very persistent dirt using a soft cloth mois-
tened with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
Filters (Fig. A)
For optimal performance it is recommended
to regularly change the filters (17,18)
depending on level of use.
1. Carefully remove cloth (17) or foam (18) filter.
2. Use a mild soap and water solution to clean the
filter and afterwards rinse with clean water.
3. Allow filter to air dry before installing and using
again.
4. Re-install the filter.
Float and filter cage (Fig. G)
Clean the float (20) and filter cage (21) regularly
with a soft cloth, and check it for damage. Other-
wise, its function can be impaired.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc VC502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc VC502AC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 6,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info