764165

Vonroc SP502AC Manual

7
Zoom out
Zoom in
Previous page
1/56
Next page
EN
7
WWW.VONROC.COM
7. After use, switch off the pump and remove the
mains plug from the mains.
8. Lift the pump back out of the water.
Manual operation
Where manual operation is preferred, the motor
can be activated by raising the float switch (3) by
hand (ON) or lowering it by hand (OFF).
Finish operation
After use allow the pump to run using clean water
for 2 - 3 minutes in order to remove residues and
particles that may have accumulated in the pump
and outlet hose.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
During maintenance or cleaning never rest
the appliance of the on the turbine
(impeller).
There are no user serviceable parts in this ap-
pliance. If the appliance appears to be blocked,
switch off the power at the mains, remove the plug
from the socket and check the appliance for block-
ages (see ‘Blockages’).
BLOCKAGES
If you suspect the pump has become blocked,
switch off the power at the mains socket remove
the plug and examine the turbine. The turbine can
be accessed by removing the securing screws in
the base and/or sub base. Alternately try reaching
the suspected blockage through the outlet (7) in
the side of the pump.
Always flush through with clean water after
every use.
STORAGE AND FROST POTECTION
The submersible pump and accessories that are
not completely drained can be destroyed by frost.
Completely drain the submersible pump and acces-
sories and protect them against frost.
Keep this appliance in well-ventilated dry premises
with temperature not going below +5°C.
When not in use, keep this appliance stored in a
safe place out of reach of children.
TROUBLE SHOOTING GUIDE
Problem Cause Remedy
Pump does not
start
No mains supply
Floater restricted
Check mains supply
Bring floater to
higher position
Pump is active
but no water is
being delivered
Turbine clogged Disconnect pump
from the power
supply and clean or
unblock the turbine
(see 'BLOCKAGES')
Pump will not
switch off
Floater restricted Bring floater to a
lower position
Pump will not
start or stops
during use.
Pump switched
off after short
operating periods
Thermal overload
safety switch has
activated
Power has tripped
Turbine clogged
Water too hot
Disconnect from
the power supply,
leave for 2 minutes
and clear the turbi-
ne (if required - see
'Blockages')
Check fuses and
electrical connec-
tions
Disconnect pump
from the power
supply and clean or
unblock the turbine
(see 'BLOCKAGES')
Ensure that the wa-
ter temperature has
not exceeded the
maximum of 35 C
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/
EU for Waste Electrical and Electronic Equipment
and its implementation into national right, power
tools that are no longer usable must be collected
separately and disposed of in an environmentally
friendly way.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc SP502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc SP502AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 6,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info