764165

Vonroc SP502AC Manual

6
Zoom out
Zoom in
Previous page
1/56
Next page
6
EN
WWW.VONROC.COM
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-3.
1. Carry handle
2. Lock (float switch)
3. Float on/off switch
4. Base
5. Hose connector
6. Water outlet elbow connector
7. Water outlet
8. Vent hole
3. ASSEMBLY
The larger the hose and hose connector
diameter, the greater the flow.
32mm (inner diameter) hose must be used
to achieve maximum flow rate.
The lower the delivery height, the greater
the flow.
Attaching the outlet hose (Fig. A, B)
1. Decide which hose diameter you are going to
use. See figure B.
2. Cut off the smaller steps of the hose connector
(5) that are not needed, using a suitable knife
or saw (not included).This removes unnecessary
flow restrictions and ensures maximum pump
capacity and water flow.
3. Screw the outlet elbow connector (6) into the
water outlet (7).
4. Screw the hose connector (5) on the outlet
elbow (6).
5. Fit the hose on to the hose connector (5) and
secure with a stainless steel hose clamp (not
included).
6. Attach a suitable rope (not included) to the
carry handle (1), to lower the pump into deep
water and to lift the pump back out of the wa-
ter. Never lower or lift the pump by its cable.
4. OPERATION
Never use this pump in a pond or swimming
pool while people are present in the water!
Never pull the pump by its power cord. The
pump must be carried by, and placed in the
water using the carry handle (1) or if the
water is deep, be lowered on a rope tied to
the carry handle (1).
Always have the pump switched off and the
plug removed from the power socket before
placing it in or removing it from the water.
Only switch the power back on with dry
hands.
Never run this pump dry - out of the water.
If the appliance overheats, the thermal
cut-out will switch it off. If this happens
wait 5 minutes before using the pump
again.
Automatic air bleed valve: The automatic air
bleed valve eliminates any air pockets in the
pump. During this process, air escapes
through the vent hole (8) and air bubbles
appear underwater. This is not a defect of
your pump, but serves to remove air from
the pump. It may take several seconds for
the air to escape when the pump is
immersed for the first time.
Automatic operation
The cable length between the float switch
(3) and the float switch lock (2) must
always be at least 10 cm.
1. To adjust the cut-in and cut-out height, attach
the float switch (3) cable to the float switch lock
(2) at the required length.
2. Lower the pump into water. It would be advisa-
ble to stand the pump on a solid platform at the
bottom to keep it upright, if practical to do so.
Ensure there are no obstructions around the in-
let openings around the base of the pump. The
inlet openings must be clear of mud or sludge
at the bottom of a pool.
3. Connect the mains plug.
4. When the pump is lowered into the water and
the power is switched on, it will start to operate
as soon as the floating switch (3) reaches the
minimum activation height (approx. 50cm) in
the water.
5. The pump switches off as soon as the float
switch (3) has reached the switch-off height
(approx. 5cm) due to the falling water level.
6. Ensure that the float switch (3) is not obstruct-
ed in any way.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc SP502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc SP502AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 6,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info