764165
5
Zoom out
Zoom in
Previous page
1/56
Next page
EN
5
WWW.VONROC.COM
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Connecting to the power supply
Check that the power supply and plug used in
accordance with your machine. Have a look at the
rating plate on the machine. Any changes should
always be carried out by a qualified electrician.
Warning! This machine must be earthed. If
not properly earthed this machine can cause
an electrical shock. Be sure that the power
supply outlet is earthed. If there is any doubt,
have it checked by a qualified electrician.
Warning! Avoid contact with the terminals
on the plug when installing (removing) the
plug to (from) the power supply outlet.
Contact will cause a severe electrical shock.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is dangerous
to insert the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm. When using a cable reel
always unwind the reel completely.
2. MACHINE INFORMATION
The pump is intended for private use for draining
flooded house and garden areas but also for trans-
ferring water to and from tanks and pumping them
out, from drawing water from wells and shafts and
for draining boats and yachts. Explosive, corrosive,
flammable substances, sewage, salt water, grease
and oil must not be conveyed by the pump.
The particle sizes of the solids in the dirty water
must not exceed the maximum particle size speci-
fied in the technical data.
This pump is not designed for continuous operation
(e.g. as a swimming pool or pond circulation pump)
or for stationary installations (e.g. lifting device,
fountain pump).
TECHNICAL SPECIFICATIONS
Model No. SP501AC SP502AC
Application Clean water Clean or
dirty water
Floating switch Yes
Voltage 230 VAC / 50Hz
Input power 300W 400W
Max. flow rate 6500l/h 8000l/h
Max. pressure 0.6 bar 0.55 bar
Max. pumping height 6m 5.5m
Max.depth 7m
Max. particle size 5mm 25mm
Min. residual water height
(manual operation) * 5mm 20mm
Switch-on height (automatic
operation) ** 50cm
Switch-off height (automatic
operation) 5cm
Max. water temperature 35°C
Protection IPX8
Built-in thermal motor pro-
tector Yes
Output hose connection 25mm, 32mm, G1"
Recommended inner hose
diameter 32mm
Water outlet G1 ¼"
Cable length 10m
Weight 3.22 kg 3.28 kg
* The stated residual water height is only
achieved in manual operation.
** The switching height can vary depending on the
position of the float switch.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc SP502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc SP502AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 6,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info